Advertisement
Operation
Phonebook
Add record
Press
.
Select [Option] > [Add new].
Follow on-screen instructions.
Call from the phonebook
Press
.
Select a record and press
Direct access memory
You have up to 9 direct access memories
(keys 1 to 9). To dial the saved phone
number automatically, press and hold on
the keys in standby mode.
Depending on your country, keys 1 and 2 are
preset to the voice mail number and
information service number of your service
provider respectively (network dependent).
Call log
Call from the call log
Press
.
Select a record and press
View record
> [Incoming calls] (D635 only) >
Press
[Option] > [View].
Save record
Press
> [Incoming calls] (D635 only) >
[Option] > [Save number].
Follow on-screen instructions.
Delete record
Press
> [Incoming calls] (D635 only) >
[Option] > [Delete].
Follow on-screen instructions.
Redial list
Call from the redial list.
Press [Redial].
Select a record and press
Save record
Press [Redial] > [Option] > [Save number].
Follow on-screen instructions.
Delete record
Press [Redial] > [Option] > [Delete].
Follow on-screen instructions.
Record an announcement
(for D635 only)
Press [Menu].
> [Announcement].
Press
to select
Follow on-screen instructions.
Register additional handsets
You can register additional handsets to
the base station.
Press [Menu].
This symbol on a product indicates that the
device is compliant with the European
Directive 2012/19/EU.
2019 © MMD Hong Kong Holding Limited
All rights reserved.
This product has been manufactured by and
is sold under the responsibility of MMD Hong
Kong Holding Limited. MMD Hong Kong
Holding Limited is the warrantor in relation to
this product.
Philips and the Philips Shield Emblem are
registered trademarks of Koninklijke Philips
N.V. and are used under license from
Koninklijke Philips N.V.
Press
Press and hold
for 10 seconds.
Enter the system PIN/Passcode (0000).
Press [OK] to confirm PIN/Passcode.
Registration is complete in less than
2 minutes.
.
Restore default settings
You can reset your phone settings to the
original factory settings.
Press [Menu].
Press
Follow on-screen instructions.
You can recover the initial PIN/Passcode
by following this procedure.
.
Battery
Philips: 2 x AAA NiMH 1.2 V Rechargeable
650 mAh batteries.
.
Use only the supplied batteries.
Adapter (base and charger)
Input:
Output:
Phonebook: 100 entries
Call log: 50 entries
Talk time: 18 hours‚
Standby time: 250 hours‚
Note
You can install a DSL (digital subscriber line)
filter to prevent noise and caller ID problems
caused by the DSL interference.
You can find the Declaration of Conformity
on www.p4c.philips.com.
To access the user instructions online, use the
reference model number written on the product
label at the bottom of the base station.
to select
[Register].
key on the base station
to select
[Reset].
Note
Technical
data
Tenpao: S003GV0600050
100-240 V~, 50/60 Hz 150 mA
6 Vdc, 500mA
Learn more
Silent mode
You can enable the silent mode for a
specified duration.
> [Silent mode]
Sound pro le
Allows you to customize the sound of voices
to your liking.
> [Sound pro le]
Eco mode
Reduces power consumption / transmission
power; reduces radiation and range by
approximately 60%.
> [Eco mode]
Eco+ mode
Eliminates radiation in standby mode
(2 seconds ring delay, 50% shorter standby
time).
> [Eco+ mode]
Privacy mode
Blocks incoming calls / block outgoing calls.
> [Call barring]/[Call block]
Frequently
Asked
Question
No signal bar is displayed on the screen.
• The handset is out of range. Move it closer to the
base station.
• If the handset displays [Register your Handset],
register your handset. (See the section on
"Register additional handsets").
If I fail to pair (register) the additional handsets to
the base station, what do I do?
• Your base memory is full. Access
[Unregister] to unregister the unused handsets
and try again.
• If registration fails, unplug the power adapter from
the base station and plug it back. Wait for 15
seconds, and then repeat the registration procedure.
I have chosen a wrong language which I cannot
read, what do I do?
Press
to go back to the standby screen.
Press
to access the main menu screen.
Press
to select
. Then you see one of the
following texts appear on the screen:
[Language]
[Langue]
[Sprache]
[Lingua]
[Dil]
Select them to access the language options.
Select your own language.
My handset is in searching or unavailable status,
what do I do?
• Make sure that the base station has power supply.
• Register the handset to the base station.
• Move the handset closer to the base station.
I cannot change the settings of my voice mail. What
do I do?
The voice mail service is managed by your service
provider but not the phone itself. Contact your
service provider to change the settings.
No display
• Make sure the batteries are charged.
• Make sure there are power and phone
connections.
The handset on the charger does not charge.
• Make sure the batteries are inserted correctly.
• Make sure the handset is placed properly on the
charger. The battery icon animates when charging.
• Make sure the docking tone setting is turned on.
When the handset is placed correctly on the
charger, you can hear a docking tone.
• The charging contacts are dirty. Disconnect the
power supply first and clean the contacts with a
damp cloth.
• Batteries are defective. Purchase new ones with
the same specifications.
Bad audio (crackles, echo, etc.)
• The handset is almost out of range. Move it closer
to the base station.
• The phone receives interference from the nearby
electrical appliances. Move the base station away.
• The walls are too thick. Move the base station
away.
The handset does not ring.
Make sure the handset ringtone is turned on.
The caller ID does not display.
• The service is not activated. Check with your
service provider.
• The caller's information is withheld or unavailable.
>
Advertisement
