8' x 6' T & G SHED
IMPORTANT, RETAIN FOR FUTURE REFERENCE;
READ CAREFULLY
This buildings is pressure treated to ensure longevity of all
timber components and to protect against rot. This may
leave a colour difference on some parts that will even out
as the moisture content stabilises. This will not require
additional treatment.
- Timber is a natural material. It will shrink and swell as a
result of varying moisture content.
- Please keep all plastic bags and small parts away from
children
- The roof of this building is not a load bearing structure.
- This product must be built on a solid level base.
- Please use suitable gloves when handling glass.
0333 7777 089
Technical Help line:
8.30 am to 5.00
pm Monday to Friday.
Check all parts prior to assembly
In line with your statutory rights, please check all parts
prior to assembly, as assembly of damaged parts may be
deemed to be acceptance and this may affect the
remedies you are entitled to. If the product is not
constructed in accordance with the instructions, or is
altered in anyway (e.g. painted), the manufacturer cannot
be held liable for any resulting damage.
Not to Scale
Fixing Pack (MTGSH86V2FP)
Rim Lock
Tee Hinge Qty 2
Handle Set
Escutcheon
Casement Stay Qty 1
Shoot Bolt
Ridge Plate
Cranked Hinge
Qty 2
REQUIRED TOOLS :
(NOT SUPPLIED)
TAPE MEASURE
SHARP KNIFE
POZI DRIVE
FLAT HEAD
SCREWDRIVER
HAMMER
SCREWDRIVER
Important : Assembly of
this shed requires a
Must Pre drill for
minimum of two adults.
each screw used.
MTGSH86 PARTS LIST
A
B
C
MTGSH86DE
MTGSH86PE
MTGSH86WS
DOOR END
PLAIN END
WINDOW PANEL
H K
H L
15120508PAII45PT
15120629PAII45PT
508mm GLAZING STRIP
629mm GLAZING STRIP
QTY 4
QTY 4
1
A
F
Place and secure two hinges to the door so that they line up with the battens on the
reverse, using 25mm Security Screws for each.
Place the door into the door end ensuring that the door is square. Fix the doors in place
using 3x25mm Security Screws for the other section of each hinge.
3
M
Place the corner strips so that they cover the joins between the
panels. Fix each in place using 3x30mm screws.
D
E
F
MTGSH46FL
MTGSH86PS
FLOOR
PLAIN PANEL
QTY 2
H
M
N
57121710PPT
1710mm CORNER STRIP
BARGE BOARD
QTY 4
QTY 4
2
Attention:
Take care
when placing
the screws.
These can
not be
backed out.
Place the panels on top of the completed floor. Make sure that all the panels are tight and flush before fixing them
to each other using 3x50mm screws.
When the panels are secured to each other, make sure they are square and fix to the floor using 3x50mm screws
for each panel ensuring that the screws are located into the bearers underneath.
4
Opening Window
H
Place the acrylic sheet inside the window frame and position the beading so that
each section fits flush and keeps the sheet tight. Fix each piece using 3 x Panel Pins.
For the opening window fix two cranked hinges to the top of the window so that it
sits in the rebate. Fix the smaller section of the hinge to the window using 2 x 25mm
screws for each. Open up the hinges and fix the remaining section of each hinge to
the top of the window panel using another 3 x 25mm screws for each hinge.
H
I
G
MTGSH86DR
MTGSH86RF
MTGWIN
XT623502
DOOR
ROOF BOARD
WINDOW
ACRYLIC SHEET
QTY 2
QTY 2
O
P
95180135PPT
DRIP STRIP
135mm LOCK BLOCK
QTY 1
QTY 1
B
C
D
5
I
L
M
K
Place and fix the Casement Stay centrally
against the inside of the opening window and
make sure it is offset at least 12mm from the to
top of the frame so as not to hit the acrylic sheet.
Fix in place using 2 x 25mm screws.
Mark the position of the holes of the casement
stay when the window is closed before fixing the
pins in place using the 25mm screws provided.
J
FIN20510012PPT
FINIAL
QTY 2
QTY 2
FELT81RED
QTY 1
Top View
C
D
Opening Window
12mm Offset
Issue 0319
Need help?
Do you have a question about the 8 x 6 T & G SHED and is the answer not in the manual?
Questions and answers