Page 1
Move to each item Change each item’s level ENTER (Process when Enter Key button ) Menu Screen 2. To enter to setting screen Press “ ENTER” Key to display a setting screen.Cursor position is shown as mark. PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
Page 2
LEFT[ ] RIGHT[ ] MASK LV BLUE CYAN MAGENTA BLACK GRAY-1 GRAY-2 GRAY-3 GRAY-4 WHILE YELLOW GREEN SHARPNESS ☒ON (Default : level 20) BLINK_POS ☒OFF ☐U_LEFT ☐U_RIGHT ☐L_LEFT ☐L_RIGHT ☐OFF ☐LOW ☐MIDDLE ☐HIGH PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
Page 3
Each Area Setting (4 Areas) MOTION AREA: Area Number ( 1 to 4 ) DETECT DISPLAY: ☒OFF ☐ON BOTTOM LEFT RIGHT SENSITIVITY PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
ALClevel It sets an average of light on screen. Use this function when an auto iris lens is used or an electrical shutter speed is fixed. Adjust ALClevel by ( )Key. Level extent is from 20 levels. PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
Page 5
2. FLICKERLESS Reduce flicker level. Switch-over [ON/OFF] by key. When you select [ON] on this menu, Item ALC/ELC is set automatically as [ALC]. Shutter Speed at flicker Model less setting PA-290 (NTSC) 1/60 PA-295 (PAL) 1/50 PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
Page 6
Set freely the photometric area of BLC which is adjusted to the under central position of people at factory setting. Set the area based on the coordinate number of each area; TOP/BOTTOM/LEFT/RIGHT by key. Convert a part of the high brightness into black of HLS level Select LOW/MIDDLE/HIGH. PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
Page 7
Level adjustment of each item is as below. 。 ITEM Contents Normal white balance setting It is displayed as ‘‘PUSHING’’ while pressing ‘ENTER’ key. White balance is calculated in the meantime, and then it is fixed once releasing PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
Page 8
It shows a natural color which people see NATW without pulling colors in. R-GAIN (0~160 Adjusts gain which ) was fixed at AWC B-GAIN (0~160 setting ) PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
Page 9
(Internal synchronization) & [L/L] (Line Lock). Change it by key. From this item; [L/L] (Line lock), you can go to the sub menu where you set phase. L/L selection Power Input 3.3~5.0 V Frequency 49.5~50.5 Hz 59.5~60.5 Hz Extent Phase Extent 30~330° 0~360° PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
Page 10
TITLE ― S elect name for each camera & position which the name is displayed on screen You can input 8 characters (MAX.) for each camera. Select alphabet by key and press ‘ENTER’ key. PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
Page 11
OSD key connector (CN5). FIY, this function cannot be used while OSD menu is shown on screen. H -MIRROR ― Horizontal Reversal Function It is used when you want to flip mirror image to horizontal axis. Switch over [ON/OFF] by key. PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
Page 12
This function is easy to avoid such problems to put a blinking mark on each position. U_LEFT Upper left (initial value) U_RIGHT Upper right D_LEFT Down left D_RIGHT Down right Remarks) Item; MOTION DETECT (Go to Page 11) is prior to Item; BLINK_POS. PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
Page 13
It positions upper and left side of the monitor (coordination:0,0,0,0) as images shown. 3. GAMMA Use the setting [0.35-0.70] on normal operation. In case that there is no necessary for Gamma correction such as image processing, use the setting [1.0] PACIFIC CORPORATION UK www.pacific-cameras.co.uk...
Save the function you set. You can use the same after turning electricity ■ NOSAVE: Not to save the function you set. Therefore it returns to the function you previously save. ■ RELOAD: Return to the function you previously save without a need to turn electricity PACIFIC CORPORATION UK www.pacific-cameras.co.uk...