Advertisement
Quick Links
Models:
SEK15A,SEK2-15A,SEK15AP,SEK2-
15AP, SEK15AH&SEK2-15AH
This manual is meant as a suppliment to the
Electric Vectaire manual, The contents herein describe the function and
operation of the Solid State Electronic Controls, For information on
Electric Vectaire Oven installation, operation, maintenance, service and parts,
refer to the Electric Vectaire manual part no. 4519-5.
These instructions should be read thoroughly before attempting installation.
Set up and installation should be performed by qualified installation personnel.
Keep area around appliances free and clear from combustibles.
PLEASE RETAIN THIS
MANUAL FOR FUTURE
REFERENCE.
Advertisement
Related Manuals for MONTAGUE Vectaire-SEK Series
Summary of Contents for MONTAGUE Vectaire-SEK Series
- Page 1 Models: SEK15A,SEK2-15A,SEK15AP,SEK2- 15AP, SEK15AH&SEK2-15AH This manual is meant as a suppliment to the Electric Vectaire manual, The contents herein describe the function and operation of the Solid State Electronic Controls, For information on Electric Vectaire Oven installation, operation, maintenance, service and parts, refer to the Electric Vectaire manual part no.
-
Page 4: Operation
***SPECIAL CAUTION*** DO NOT PLACE HIGH-HEAT PRODUCING EQUIPMENT ADAJACENT TO THE RIGHT SIDE OF AN "SEK" VECTAIRE CONVECTION OVEN. EXCEEDING 185 DEGREES (F) (85 C) SURFACE TEMPERATURES CAN CAUSE PREMATURE COMPONENT FAILURE NOT COVERED UNDER THE MANUFACTURERS WARRANTY. OPERATION CONTROLS STANDARD MODELS (SEK15A AND SEK2=15A-FIGURE 1) "LIGHT-OFF"... - Page 5 COOK-N-HOLD MODELS (IE; SEK15AH AND SEK2=15AH--FIG. 3) KEY PAD CONTROLS IN ADDITION TO THE KEYS STANDARD WITH THE PROGRAMMABLE MODE, COOK-N-HOLD MODELS INCLUDE COOK-HI-FAN AND ROAST-LOW- FAN KEYS WITH WHICH TO CHANGE THE FAN SPEED. THERE IS ALSO A HOLD KEY WHICH ALLOWS A HOLD TEMPERATURE TO BE MANUALLY SET OR PROGRAMMED INTO MEMORY.
- Page 6 WILL BEGIN. THE BEEP IS CANCELLED BY PRESSING ANY KEY OR TURNING EITHER ROTARY DIAL, ALTHOUGH THE START/TIMER OR CANCEL KEYS ARE INTENDED TO BE USED FOR BEEP CANCELLING. TIME CAN BE INCREASED DECREASED DURING TIMING CYCLE ROTATING THE TIME KNOB CLOCKWISE COUNTERCLOCKWISE...
- Page 7 ACCESS SET THE TIME DIGITS OF THE CONTROL TO OOSOO. SET THE COOK TEMPERATURE TO (X 10 ) ("X" STANDS FOR ANY NUMBER) PUSH AND HOLD THE START/TIMER KEY FOR 5 SECONDS. OPERATION EITHER ROTARY DIAL IS TURNED UNTIL DESIRED OFFSET IS DISPLAYED.
- Page 8 ALLOWS A BAKE TO RISE AND TAKE A SET BEFORE BEING EXPOSED TO THE FULL FORCE OF THE CONVECTED AIR IN THE OVEN. THE IFO OPTION CAN BE ADDED AT THE FACTORY TO ALL MONTAGUE GAS AND ELECTRIC CONVECTION OVENS EXCEPT THE MODELS 70Z AND 115Z.
- Page 9 IFO CONTROLS ARE INSTALLED AT THE FACTORY, AND THE CONVECTION OVENS SHOULD INSTALLED ACCORDANCE WITH MONTAGUE •••S STANDARD INSTALLATI ON INSTRUCTIONS. ***SPECIAL CAUTION*** IFO FAN CONTROL OPTION INCLUDES SOLID-STATE COMPONENTS. PLACE HIGH-HEAT PRODUCING EQUIPMENT ADJACENT TO THE RIGHT SIDE OF AN...
- Page 10 Service Instructions for A11 SE and SEK Solid State Control Panels THERMOSTAT ADJUSTMENT The SE and SEK temperature controllers use solid state components and NEVER needs calibration as long as the control is operating properly. FAULT DIAGNOSIS Six failure modes are provided to aid in trouble shooting oven malfunctions and to inform the user of problems. Each failure has an associated code number that is displayed when the failure occurs.
Need help?
Do you have a question about the Vectaire-SEK Series and is the answer not in the manual?
Questions and answers