Download Print this page
Toro GrandStand 134-3259 Installation Instructions Manual
Toro GrandStand 134-3259 Installation Instructions Manual

Toro GrandStand 134-3259 Installation Instructions Manual

Mulching kit mower with 122cm rear discharge turbo force cutting unit

Advertisement

Quick Links

Mulching Kit
GrandStand
Cutting Unit
Model No. 134-3259
Safety
Rear Discharge or Mulch
Grass
WARNING
Without the grass deflector mounted in place,
you and others are exposed to blade contact
and thrown debris. Contact with rotating
mower blade(s) and thrown debris will cause
injury or death.
• Never remove the grass guard from the
mower because the grass guard routes
material down toward the turf. If the
grass guard is ever damaged, replace it
immediately.
• Never put your hands or feet under the
mower.
• Never try to clear the discharge area or
mower blades unless you engage the
parking brake, disengage the power take
off (PTO) lever, shutoff the engine, remove
the ignition key, and wait for all motion
to stop. Also pull the wire off the spark
plug(s).
Ensure that the mower has the rear grass guard to
disperses clippings to the rearward and down toward
the turf, while in rear discharge mode.
To mulch grass clippings, install the baffles on the
mower deck as instructed in the following procedures.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Mower With 122cm Rear Discharge TURBO FORCE
Register at www.Toro.com.
Form No. 3431-158 Rev C
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3431-158* C
Printed in the USA
®

Advertisement

loading
Need help?

Need help?

Do you have a question about the GrandStand 134-3259 and is the answer not in the manual?

Questions and answers

Summary of Contents for Toro GrandStand 134-3259

  • Page 1 To mulch grass clippings, install the baffles on the mower deck as instructed in the following procedures. © 2019—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3431-158* C...
  • Page 2: Installation

    Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the mower. – No parts required Open the engine guard. – No parts required Remove the left belt cover. –...
  • Page 3: Preparing The Mower

    Preparing the Mower No Parts Required Procedure Note: Determine the left and right sides of the machine from the normal operating position. Park the machine on a level surface; disengage the cutting unit(s) and lower the cutting unit; engage the parking brake; shut off the engine and remove the key;...
  • Page 4 Removing the Guard Extension Remove the 2 bolts (5/16 x 1 inch) and belt guard (Figure Removing the Left Belt Cover No Parts Required Procedure Remove the 2 flange-head screws that secure the tensioner cover to the left belt cover, and remove the tensioner cover (Figure g279540...
  • Page 5 g270486 Figure 6 1. Right belt cover 3. Flange-head screw (left and right belt cover) 2. Flange (left belt cover) Remove the 2 carriage bolts and 2 locknuts that secure the left side CE cover to the left belt cover (Figure g270488 Figure 8...
  • Page 6 Drilling the Baffle and Kicker Fitting Holes Note: Determine the left and right sides of the machine from the normal operating position. Drilling the Mower Deck At the left side of the mower deck, drill the pilot hole in the deck with a 10 mm (3/8 inch) drill bit No Parts Required as shown in Figure...
  • Page 7 g284201 g284197 g284202 Figure 11 1. Pilot hole (mower deck) 2. 10 mm (3/8 inch) drill bit At the bottom of the mower deck, drill the 6 pilot holes in the deck with a 10 mm (3/8 inch) drill bit as shown in Figure g284198...
  • Page 8 Remove any burrs from the holes that you drilled. Installing the Baffle Supports Parts needed for this procedure: g284228 Figure 15 Left baffle support 1. Front of the machine 3. Deflector bracket Center/right baffle support 2. Carriage bolt (5/16 x 7/8 4.
  • Page 9 carriage bolts (5/16 x 1-1/4 inch) and 2 flange locknuts (5/16 inch). Torque the 2 flange locknuts to 20 to 25 N∙m (15 to 18 ft-lb). Installing the Right Baffle Support Note: Determine the left and right sides of the machine from the normal operating position.
  • Page 10 Installing the Center Baffle Support Note: Determine the left and right sides of the machine from the normal operating position. At the top of the mower deck, insert 2 flange-head bolts (5/16 x 3/4 inch) through the 8 mm (5/16 inch) holes that you drilled in Drilling the Center Baffle Support Holes (page g284248...
  • Page 11 Align the holes in the center baffle with the hole in the right divider, the hole in the other center/right baffle support, and the left divider as shown in Figure g284121 Figure 21 1. Left baffle 3. Right baffle 2. Center baffle Installing the Baffles Note: Determine the left and right sides of the...
  • Page 12 Installing the Kicker Fittings Parts needed for this procedure: Kicker fitting Carriage bolt (3/8 x 1 inch) Flange locknut (3/8 inch) Procedure g284291 Note: Determine the left and right sides of the machine from the normal operating position. At the right side of the mower deck, align the slots in the kicker fitting with the 2 holes 10 mm (3/8 inch) that you drilled into the mower deck (Figure...
  • Page 13 (3/8 inch) that you drilled into the mower deck (Figure 26). g284380 g284378 g284381 Figure 27 1. Kicker fitting 4. Carriage bolt (3/8 x 1 inch) g284379 Figure 26 2. Flange locknut (3/8 inch) 5. 10 mm (3/8 inch) holes—mower deck 1.
  • Page 14 Installing the Recycler Blades Parts needed for this procedure: Recycler blades (sold separately) Procedure WARNING A blade is sharp. Contact with a sharp blade can cause serious personal injury. Wear gloves or wrap sharp edges of the blade with a rag. Install the recycler blades onto the mower;...
  • Page 15 Installing the Guard Extension and Closing the Engine Guard No Parts Required Installing the Guard Extension g270486 Figure 30 Install the extension guard as shown in Figure 1. Right belt cover 3. Flange-head screw (left 32. Torque the nuts to 20 to 25 N∙m (15 to 18 and right belt cover) ft-lb).
  • Page 16 Secure the engine guard to the extension guard using the bolt and shoulder nut as shown in Figure g279540 Figure 33 1. Bolt (5/16 x 1 inch) 2. Belt guard g279539 Figure 35 Connecting the Spark-Plug Wire 1. Bolt and shoulder nut 2.
  • Page 17 Removing the Kicker Fittings 2 flange locknuts (3/8 inch) that you removed in step 2. Note: Determine the left and right sides of the machine from the normal operating position. At the bottom left side of the mower deck, remove the 2 carriage bolts (3/8 x 1 inch) and 2 flange locknuts (3/8 inch) that secure the kicker fitting to the deck, and remove the kicker fitting (Figure...
  • Page 18: Removing The Baffles

    deck (Figure 42) and secure the capscrews with the flange locknut (3/8 inch) that you removed in step 1. g284406 Figure 40 1. Flange locknut (3/8 inch) 3. Flange-head capscrew (3/8 x 1 inch) 2. 10 mm (3/8 inch) holes—mower deck g284407 Figure 42 Note:...
  • Page 19 Removing the Baffle Brackets Remove the 2 flange locknuts (5/16 inch) that secure the left baffle support (Figure 46). g284292 Figure 44 1. Right side plate (mower 5. Right baffle deck) 2. Right divider 6. Carriage bolt (3/8 x 1 inch) 3.
  • Page 20 g287228 Figure 47 1. Flange-head bolts (5/16 x 4. Flange locknut (5/16 inch) 3/4 inch) 2. Carriage bolts (5/16 x 5. Front of the machine 1-1/4 inch) g287226 3. Center and right baffle 6. Left baffle support Figure 48 supports 1.
  • Page 21: Operation

    Finishing Converting the Mower Operation Deck for Rear-Discharge Operation Selecting the Proper Height Install the non-recycling blades; refer to the Operator’s Manual for your machine. of Cut Install the left belt cover; refer to 10 Installing the Left Belt Cover (page 14).
  • Page 22 Notes:...
  • Page 23 Notes:...