Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Ingersoll-Rand SS5L5
Summary of Contents for Ingersoll-Rand SS5L5
- Page 1 RELEASED 05/Apr/2018 15:16:08 GMT 22204945 Revision C March 2018 SS5L5 SS5N5 Owner’s Manual With Parts List Owner’s Manual With Parts List Manual del propietario con la lista de piezas Manuel du propriétaire avec liste des pièces Save These Instructions...
-
Page 2: Table Of Contents
RELEASED 05/Apr/2018 15:16:08 GMT CONTENTS SAFETY ........4 MAINTENANCE . - Page 3 RELEASED 05/Apr/2018 15:16:08 GMT May 2015 22204945 Rev C EN-3...
-
Page 4: Safety
RELEASED 05/Apr/2018 15:16:08 GMT SAFETY Indicates an imminently hazardous WARNING situation which, if not avoided, will result in death or serious injury. A hazardous voltage can cause serious injury or death. Indicates a potentially hazardous situation WARNING Disconnect power and bleed pressure from the tank before which, if not avoided, could result in death servicing. -
Page 5: Receipt & Inspection
RELEASED 05/Apr/2018 15:16:08 GMT RECEIPT & INSPECTION Ensure adequate lifting equipment is available for unloading and moving If you discover damage after receiving the unit (concealed damage), the the compressor to the installation site. carrier must be notified within 15 days of receipt and an inspection must be requested by telephone with confirmation in writing. -
Page 6: Installation
RELEASED 05/Apr/2018 15:16:08 GMT INSTALLATION SELECTING A LOCATION Typical Permanent Mounting (Customer -Supplied Hard- ware) GENERAL Select a clean, dry, well-lighted indoor area with plenty of space for proper cooling air flow and accessibility. Locate the unit at least 12 inches (30 cm) Flat Washer from walls, and make sure the main power supply IS clearly Identified and 3/8”... -
Page 7: General Requirements
RELEASED 05/Apr/2018 15:16:08 GMT WIRE SIZE SYNTHETIC COMPRESSOR LUBRICANT MATERIAL COMPATIBILITY The electrical wiring between the power supply and electric motor varies LIST according to motor horsepower. Power leads must be adequately sized COMPATIBILITY LIST SUITABLE : to protect against excessive voltage drop during start-up. Information for selecting the proper wire size and securing connections should be FKM (Fluoroclastomer), PTFE, Epoxy (Glass Filled), Oil Resistant Alkyd, provided with the motor. -
Page 8: Filling Procedures
If you use a petroleum-based compressor lubricant at start-up and decide CAUTION to convert to Ingersoll Rand synthetic compressor lubricant later on, the compressor valves must be thoroughly decarbonized and the crankcase must be flushed before conversion. Unusual noise or vibration indicates a problem. Do not continue to operate until you identify and correct the source of the FILLING PROCEDURES: problem. -
Page 9: Operation
RELEASED 05/Apr/2018 15:16:08 GMT OPERATION GENERAL WHEN YOU ARE FINISHED: Your air compressor was designed for 100% continuous duty operation Set the pressure switch lever to ‘OFF”. with the use of Ingersoll Rand svnthetic compressor lubricant and 60% Close the service valve fully. continuous duty operation with the use of petroleum lubricant. -
Page 10: Maintenance
RELEASED 05/Apr/2018 15:16:08 GMT MAINTENANCE FILTER REPLACEMENT (SS5) WARNING Unscrew and remove the wing nut (A) securing the filter housing (B) Disconnect, lock and tag the main power supply and release air to its base (C). pressure from the system before performing maintenance. Remove the filter busing and withdraw the old filter element (D) Clean the element with a jet of air or vacuum. -
Page 11: Belt Adjustment
RELEASED 05/Apr/2018 15:16:08 GMT BELT ADJUSTMENT CAUTION • CHECKING BELT TENSION Improper pulley/sheave alignment and belt tension can result in Check belt tension should be occasionally, especially if looseness is motor overload, excessive vibration, and premature belt and/or suspected. A quick check to determine if adjustment is proper may be bearing failure. -
Page 12: Troubleshooting
RELEASED 05/Apr/2018 15:16:08 GMT TROUBLESHOOTING PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION Lubricant viscosity too low Drain existing lubricant and refill with proper lubricant. Lubricant level too low Add lubricant to crankcase to proper level. Detergent type lubricant being used Drain existing lubricant and refill with proper lubricant Abnormal piston, ring or cylinder wear. - Page 13 RELEASED 05/Apr/2018 15:16:08 GMT PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION Loose beltwheel or motor pulley, excessive Check beltwheel, motor pulley, crankshaft, end play in motor shaft or loose drive belts. drive belt tension and alignment. Repair or replace as required. Lubricant viscosity too high Drain existing lubricant and refill with proper lubricant Lubricant level too low...
- Page 14 PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION Improper line voltage Check line voltage and upgrade lines as required. Contact electrician. Wiring or electric service panel too small Install properly sized wire or service box. Contact electrician. Lights flicker or dim when running Poor contact on motor terminals or starter Ensure good contact on motor terminals or connections...
- Page 15 RELEASED 05/Apr/2018 15:16:08 GMT PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION Lubricant viscosity too low Drain existing lubricant and refill with proper lubricant Detergent type lubricant being used Drain existing lubricant and refill with proper lubricant Piston rings damaged or worn (broken, rough Install ring kit or scratched).
-
Page 16: Warranty And Limitation Of Liability
RELEASED 05/Apr/2018 15:16:08 GMT WARRANTY AND LIMITATION OF LIABILITY WARRANTY Ingersoll Rand company warrants that the equipment manufactured by it and delivered hereunder shall be free of defects in material and workmanship for a period of twelve (12) months from the date of placing the equipment in operation or eighteen (18) months from the date of shipment, whichever shall occur first. - Page 17 RELEASED 05/Apr/2018 15:16:08 GMT 22204945 Rev C EN-17...
- Page 18 RELEASED 05/Apr/2018 15:16:08 GMT REF. NO. PART NO. DESCRIPTION QTY. CANT. QTÉ. REF. 97334148 PUMP, BARE COMPRESSOR 20102703 SET, PISTON RING RING, COMPRESSION RING, SCRAPER RING, OIL CONTROL SPACER RING, OIL CONTROL 95033593 PLUG, OIL DRAIN 96706874 CAPSCREW. M8X65 (HEAD BOLT) 96702253 CAPSCREW.
- Page 19 RELEASED 05/Apr/2018 15:16:08 GMT 54429600 GASKET, VALVE PLATE 97333546 GASKET, CYLINDER 54410667 GASKET, HEAD 97334270 GLASS, SIGHT 54410683 HEAD 70243936 ASSEMBLY, VENT 54406640 FILTER, INLET 32170979 ELEMENT, FILTER NOT SOLD SEPARATELY AVAILABLE lNDlVlDUALLY OR IN VALVE KIT 20100277 AVAILABLE INDIVIDUALLY OR IN PISTON RING KIT 20100285 22204945 Rev C EN-19...
-
Page 20: Parts List
RELEASED 05/Apr/2018 15:16:08 GMT PARTS LIST REF. NO. PART NO. DESCRIPTION QTY. 84G03724 CAPSCREW 95750394 WASHER SPRING LOCK 97334148 PUMP. BARE COMPRESSOR BELTGUARD GROUP ASSEMBLY COMPLETE BELTGUARD 32188518 BRACE, BELTGUARD 56280159 SCREW, HEX- SERRATED FLANGE- M6-1.0X 12MM 54416730 BELTGUARD, FRONT 54416748 BELTGUARD, BACK 97173595... - Page 21 VALVE, BALL- 1/2 F/F (SERVICE VALVE) 56291412 TANK, AIR RECEIVER -SSSL5 22108781 TANK, AIR RECEIVER - SS5N5 85582229 VALVE, CHECK- SS5L5 97333165 VALVE, CHECK-SS5N5 56269608 GAUGE, PRESSURE - SS5L5 32499816 GAUGE, PRESSURE - SS5N5 54372834 SWITCH, PRESSURE-SS5L5 54627104 SWITCH, PRESSURE:-SS5N5 97004030 CONNECTOR CABLE 56269624...
-
Page 22: Kits & Accessories
RELEASED 05/Apr/2018 15:16:08 GMT KITS & ACCESSORIES EXTENDED WARRANTY KIT MULTIPURPOSE AIR HOSES Each extended warranty kit contains air filters and all season select These air hose assemblies are heavy duty, light weight hoses designed for lubricant sufficient for two years operation. 300 PSIG working pressure. - Page 23 RELEASED 05/Apr/2018 15:16:08 GMT...
- Page 24 RELEASED 05/Apr/2018 15:16:08 GMT ingersollrandproducts.com © 2018 Ingersoll-Rand...