Advertisement
Quick Links
GARDENSHED
1.51W x 0.77D x 1.9Hm
Skillion Series
Assembly instructions
Congratulations on purchasing your new Pinnacle garden shed. Before assembling, we recommend
you read the instructions thoroughly. Your new garden shed comes with pre-drilled holes to make
assembly quicker. We recommend you assemble it using a trestle table or sawhorses and planks.
This will ensure that you are working off the ground and make it easier for you.
Assembly of this shed is a two-person job and should not be attempted in windy conditions.
Tools required: Drill, measuring tape, Phillips-head screw driver, rivet gun, rubber mallet, sturdy ladder, shifting spanner, 2 saw horses, 3mm
steel drill bit, 4mm steel drill bit and a 10mm masonry drill bit.
www.pinnacle.net.au
Check out our
shed building
tips on Youtube!
AU: 1800 349 776
NZ: 09 276 4071
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Pinnacle Skillion Series
Summary of Contents for Pinnacle Skillion Series
- Page 1 AU: 1800 349 776 NZ: 09 276 4071 Congratulations on purchasing your new Pinnacle garden shed. Before assembling, we recommend you read the instructions thoroughly. Your new garden shed comes with pre-drilled holes to make assembly quicker. We recommend you assemble it using a trestle table or sawhorses and planks.
- Page 2 GARDENSHED 1.51W x 0.77D x 1.9Hm Dimension overview: Outer base dimensions 1515 x 775 mm Inner base dimensions 1470 x 730 mm Wall height 1800 mm Peak height 1905 mm Roof width 856 mm Door opening dimensions 1740 x 746 mm...
- Page 3 Build your garden shed in 7 easy steps! Step 1: Check all parts against the component list Step 2: Assemble the rear wall panels Step 3: Assemble the side wall panels Step 4: Assemble the roof panels Step 5: Assemble the front wall panel Step 6: Assemble the front door Step 7: Fit the panels together Warning: Do not assemble this shed on a windy day.
- Page 4 GARDENSHED 1.51W x 0.77D x 1.9Hm Step 1: Check all parts against the component list Lay out all parts with number facing outwards and check off against parts list. Part Picture Description Component Location QTY Check Sheet Sheet 1880x770mm Rear wall Sheet 1800-1880x770mm Sheet Side wall...
- Page 5 Part Picture Description Component Location QTY Check Channel Channel 1508mm Rear wall Channel Channel 1508mm Front Channel Channel 1508mm Front Channel Channel 768mm Side wall Channel Channel 768mm Side wall Channel Channel 775mm Front Channel Channel 1458mm Rear wall Channel 718mm Channel Side wall Channel 674mm...
- Page 6 GARDENSHED 1.51W x 0.77D x 1.9Hm Part Picture Description Component Location QTY Check Brace Corner brace Corner Brace Corner brace Corner Brace Corner brace Corner Lip 856mm Roof Brace Joining brace Door Fittings part list: Picture Component Picture Component Self-tapping screws (10mm) Self-tapping screws (16mm) 4 x 10mm Rivet 3 x 10mm Rivet...
- Page 7 Signature: _________________________________________ In the unlikely event that you find you are missing a part, Australian customers please contact Pinnacle on 1800 349 776. New Zealand customers please contact Harco (Harkness & Young Ltd) on: 09 276 4071. A copy of proof of purchase may be requested.
- Page 8 GARDENSHED 1.51W x 0.77D x 1.9Hm Step 2: Assemble the rear wall panels You will find it easier to assemble your shed using sawhorses with timber studs attached (timber needs to be the same length as the shed (1.5m) or alternatively, a trestle table. Place 2 x part S83 (Sheet) on your worktable and join them together with the self-tapping screws as per diagram below.
- Page 9 ROOF TOP EDGE RIDGES FACING UP Assemble the rear wall panels (continued) Step 2: Now fit part 31 (mid wall channel) to the sheeting and position it with the provided self-tapping screws. Please note the groove should face downwards. Position the top and bottom channels with self-tapping screws as well. NOTE: All screws marked with a cross should not be fixed at this stage.
- Page 10 GARDENSHED 1.51W x 0.77D x 1.9Hm Assemble the side wall panels Step 3: Place part S84 (sheet) on your worktable and tap or slide in part 21A (top channel) and part 21B (bottom channel). Position and fix part 32 (mid wall channel) using the self-tapping screws ensuring this channel is facing down before fixing. Fix part 21B (bottom channel) with self-tapping screws but not part 21A (top channel) at this stage.
- Page 11 Assemble the roof panel Step 4: Place 2 x part 3 (sheet) on your worktable and join together with the self-tapping screws as per the diagram below. Now tap or slide 2 x part 20A (channels) onto the sheeting and fix them to the top and bottom with self-tapping screws. Make sure that the small lips on channels 20A are always facing out.
- Page 12 GARDENSHED 1.51W x 0.77D x 1.9Hm Assemble the roof panel (continued) Step 4: Now fit 2 x part 50 (side lips) to the sheeting and fix them with self-tapping screws.
- Page 13 Step 5: Assemble the front wall panels Place part S86 (sheet) on the worktable. Fit part 20D (top channel), part 20E (bottom channel), part J3 (jamb) (There are pre-drilled holes for the next step on both parts S86 and J3 that must be aligned) and part 33R (mid wall channel) to the sheeting and fix them with self-tapping screws - except those marked with a cross.
- Page 14 GARDENSHED 1.51W x 0.77D x 1.9Hm Assemble the front door Step 6: Place part D18R (door sheet) on the worktable. Fit 2 x part M26, part M24 and part M25 (channels) to the door with the provided 3.0 x 10mm rivets. Make sure that the small lips on channels M26 are always facing out. This ensures rainwater cannot build up inside your shed.
- Page 15 Assemble the front door (continued) Step 6: Once channels are fitted to both doors, align 2 x part U11 (brace) and part W (joining brace) with holes on the back of the door and position temporarily with some tape or simply hold in place. ROOF TOP EDGE D18R BACK...
- Page 16 GARDENSHED 1.51W x 0.77D x 1.9Hm Assemble the front door (continued) Step 6: Turn door over with bracing aligned with holes (make sure the ridges of the door are facing up) and fix the bracing with the provided 3.0 x 10mm rivets through the front of the panel. Then turn door over and insert plastic stoppers at the ends of braces as shown below.
- Page 17 Assemble the front door (continued) Step 6: Fit part D18R (assembled door) to the front wall panel as per the diagram below. Use rivet gun to fix the door using the pre-drilled holes. Fix the pad bolt (but NOT its keeper at this stage) using the pre-drilled holes with the self-tapping screws (or rivets) provided. ROOF TOP EDGE RIDGES FACING UP D18R...
- Page 18 GARDENSHED 1.51W x 0.77D x 1.9Hm Fit the panels together Step 7: Attach the two side walls to the back wall, then fix the front wall followed by the roof. Fix all of these components together using the provided self-tapping screws. Fix the pad bolt keeper with the provided 16mm self-tapping screws (diagram A) or using rivets (diagram B) at this stage as well.
- Page 19 Fit the panels together (continued) Step 7: Now fit the bolt down kit as per the diagram below. Strengthen the mid wall braces by applying part 72 (mid wall brace bracket) on each corner if necessary. BOLT & NUT WALL SHEET STEEL ANGLE SLAB DOOR...
- Page 20 GARDENSHED 1.51W x 0.77D x 1.9Hm Fit the panels together (continued) Step 7: For safety apply channel safety cover (L type) to part 32 (channel) and channel safety cover (R type) to 33R (channel). Also apply the self-tapper covers to screw ends visible in the walls on the inside of the shed as per the diagram below.
- Page 21 Fit the panels together (continued) Step 7: The door can be hinged on the opposite side as well. Align the door with the edge and make the holes using a cordless drill. Remove the pins from the hinges and reverse their direction before you attach the door. If you are concerned about the visibility of any pre-drilled holes, you can fill them with rivets.
- Page 22 Process of claiming Warranty: To make a claim under the Warranty within the Warranty Period, you will need to contact the manufacturer directly by phone or email: Australian Customers please contact Pinnacle Hardware on: Claims Department contact number: 1800 349 776 Claims Department email: support@pinnacle.net.au...
- Page 23 – Where assessment is required in case of replacing or repairing the product, the manufacturer will appoint an assessor within 10 working days to identify the alleged defect. The manufacturer will bear the repair costs by appointing a local tradesman. The manufacturer may choose to replace the product if the repair or the cost of repair is not feasible.
Need help?
Do you have a question about the Skillion Series and is the answer not in the manual?
Questions and answers