Download Print this page
Husqvarna CF 11M Operator's Manual

Husqvarna CF 11M Operator's Manual

Frequency converter


CF 11M, CF 25M, CF 25T, CF 67T,
Operator's manual



Summary of Contents for Husqvarna CF 11M

  • Page 1 CF 11M, CF 25M, CF 25T, CF 67T, CF 67TCI4P Operator's manual 2-12...
  • Page 2: Table Of Contents

    Contents Introduction..............2 Troubleshooting.............. 7 Safety................4 Storage and disposal............8 Operation................ 6 Technical data..............9 Maintenance..............7 EC Declaration of Conformity........12 Introduction Product overview 1. Operator's manual 10. OFF button, red 2. Handle 11. Rating plate 3. Connection box 12.
  • Page 3 vibrators. The product is used connected to a power 1. Product type outlet. The product operates as a transformer to make 2. Serial number sure that the operation of the concrete vibrators is safe. 3. Speed, rpm The green and red buttons on the product have an 4.
  • Page 4: Safety

    Safety Safety definitions • Keep the product clean. Make sure that you can clearly read signs and decals. Warnings, cautions and notes are used to point out • Do not use the product if it is defective. specially important parts of the manual. •...
  • Page 5 Husqvarna service agent. • Do a check that the power cord and the power plug are in good condition and not damaged.
  • Page 6: Operation

    • If the maintenance is not done correctly and by the manufacturer, can cause serious injury or regularly, the risk of injury and damage to the death. product increases. • Replace damaged, worn or broken parts. • Use personal protective equipment. Refer to •...
  • Page 7: Maintenance

    Maintenance Daily maintenance • Make sure that screws and glands are sealed against water. • Clean the external surface. Maintenance after long-term storage • Tighten cable connections fully. • Make sure that the ON/OFF buttons operate Let a service agent do a check of the insulation between correctly.
  • Page 8: Storage And Disposal

    Problem Cause Solution The vibration speed There is overload in the product. Make sure that the total nominal consump- in the concrete vibra- tion of the connected concrete vibrators is tor is too low. lower than the nominal output from the prod- uct.
  • Page 9: Technical Data

    Technical data Technical data CF67T, CI4P, 400 V CF67T, CI4P, 440 V CF67T, CI4P, 380 V Weight, kg/lb 70/154 70/154 70/154 Height, mm/in. 690/19.60 690/19.60 690/19.60 Length, mm/in. 775/18.11 775/18.11 775/18.11 Width, mm/in. 460/18.89 460/18.89 460/18.89 Input voltage, V Phases Input frequency, Hz Input current, A 10.5...
  • Page 10 CF25T, 400 V CF25T, 440 V CF25T, 380 V CF25M Output current, A Output power, kVA Wheels Yes (optional) Yes (optional) Yes (optional) Yes (optional) Number of outlets Protection index IP55 IP55 IP55 IP55 Primary voltage tolerance ±10% ±10% ±10% ±10% Ambient temperature, °C -10 to +40...
  • Page 11 Noise emissions CF11M CF25M CF25T CF67T CF67T CI4P Sound pressure level L at the operators ear, dB(A) Noise and vibration declaration statement These declared values were obtained by laboratory type testing in accordance with the stated directive or standards and are suitable for comparison with the declared values of other products tested in accordance with the same directive or standards.
  • Page 12: Ec Declaration Of Conformity

    Brand Husqvarna Type/Model CF 11M, CF 25M, CF 25T, CF 67T, CF 67TCI4P + AX 36, AX 40, AX 48, AX 56, AX 65, AX 90, Vibrastar 40, Vibrastar 50, Vibrastar 60 Identification Serial numbers dating from 2019 and onwards...
  • Page 13 1381 - 002 - 12.03.2020...
  • Page 14 1381 - 002 - 12.03.2020...
  • Page 15 1381 - 002 - 12.03.2020...
  • Page 16 Original instructions 1142122-26 2020-03-16...

This manual is also suitable for:

Cf 25mCf 25tCf 67tCf 67tci4p