Operation - Matco Tools MT2465 Operating Instructions Manual

failure To oBserVe These Warnings could resulT in inJury
This insTrucTion Manual conTains
iMporTanT safeTy inforMaTion.
read This insTrucTion Manual carefully
and undersTand
Before operaTing This Tool.
• Always operate, inspect and maintain this tool in
accordance with American National Standards
Institute Safety Code of Portable Air Tools (ANSI
B186.1) and any other applicable safety codes
and regulations.
• For safety, top performance and maximum durability
of parts, operate this tool at 90 psig 6.2 bar max
air pressure with 3/8" diameter air supply hose.
• Always wear impact-resistant eye and face
protection
maintenance on this tool.
• Always wear hearing protection when using this
tool. High sound levels can cause permanent hearing
loss. Use hearing protection as recommended by
your employer or OSHA regulation.
• Keep the tool in efficient operating condition.
• Operators and maintenance personnel must be
physically able to handle the bulk, weight and
power of this tool.
• Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions over
extended periods of time may be harmful to
your hands and arms. Discontinue use of tool if
discomfort, tingling feeling or pain occurs. Seek
medical advice before resuming use.
• Air under pressure can cause severe injury. Never
direct air at yourself or others. Always turn off the
air supply, drain hose of air pressure and detach
tool from air supply before installing, removing
or adjusting any accessory on this tool, or before
performing any maintenance on this tool. Failure
to do so could result in injury. Whip hoses can
cause serious injury. Always check for damaged,
frayed or loose hoses and fittings, and replace

operaTion

Select a suitable abrasive disc and make sure that it is fixed securely
to the pad. Connect a suitable air supply as recommended. The
air inlet used for connecting air supply has standard 1/4" NPT
thread.
Apply the sander lightly to the work and allow the abrasive disc
to cut. Take great care when sanding around sharp edges and
surfaces to avoid the disc snagging, i.e. the disc may be brought
to an abrupt stop or considerably slowed which will cause the
tool to kick in the operator's hands. It is always recommended to
use safely glasses and a breathing mask. The sanding of certain
materials may create a hazardous dust which may require special
breathing equipment. Check before using the tool. Even if the
machine has a low noise level, the actual sanding process may
cause a noise level such that ear protectors will be required.
MT2465/MT2470
MT2465/MT2470
all inforMaTion
when operating or performing
6" & 8" Geared Sander
immediately. Do not use quick detach couplings at
tool. See instructions for correct set-up.
• Place the tool on the work before starting the tool.
• Slipping, tripping and/or falling while operating
air tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
• Keep body working stance balanced and firm. Do
not overreach when operating the tool.
• Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
• Do not carry tool by the hose. Protect the hose from
sharp objects and heat.
• Tool shaft may continue to rotate briefly after throttle
is released Avoid direct contact with accessories
during and after use. Gloves will reduce the risk of
cuts or burns.
• Keep away from rotating end of tool. Do not wear
jewelry or loose clothing. Secure long hair. Scalping
can occur if hair is not kept away from tool and
accessories. Choking can occur if neckwear is not
kept away from tool and accessories.
• Never mount a grinding wheel on a sander. A
grinding wheel that bursts can cause very serious
injury or death when not properly guarded. Inspect
backing pad before each use. Do not use if cracked
or damaged.
• Avoid direct contact with moving sanding pad to
prevent pinching or cutting of hands or other body
parts.
• Use accessories recommended by Matco Tools.
• Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace damaged
labels.
If there are sharp areas on the material being sanded, safety gloves
are recommended. Do not continue to use abrasive discs that are
worn or clogged. This will make the sanding process inefficient and
the need to apply unnecessarily high forces to the tool. Do not use
undersized or oversized sanding discs. The disc should be no more
that 1/4" larger in diameter than the pad and not smaller than
the pad. An air regulator (14) is located on the side of the motor
housing (1). It can be used to vary the volume of compressed air
fed to the motor which will vary the speed of the sander.
2 Rev. 06/30/10