Matco Tools MT2422 Manual

WARNING
Study, understand and follow all instructions provided
with this product. Read these instructions carefully
before installing, operating, servicing or repairing this
tool. Keep these instructions in a safe accessible place.
INTENDED USE OF THE TOOL
This surface prep tool is designed for sanding metal,
plastic and painted surfaces to strip paint, gaskets,
or for. Do not use this tool outside of the designed
intent. Never modify the tool for any other purpose
or use.
WARNING
Caution: To help prevent personal injury
• Normal use of this product is likely to expose the user to
dust and/or microscopic particles containing chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm. Always wear
appropriate safety equipment and clothing when using
this product. Study, understand and follow all
instructions provided with this product. Failure to read
and follow all warnings and operating instructions may
result in damages and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and Bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with
accessories not designed for it could result in serious
injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to
perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
MICRO SURFACE
PREP TOOL
The manufacturer warrants this product to the original user against defective
material or workmanship for a period of 1 year from the date of purchase.
The manufacturer reserves the right to determine whether the part or parts
failed because of defective material, workmanship or other causes.
Failures caused by accident, alteration or misuse are not covered by this
warranty.
The manufacturer, at its discretion, will repair or replace product covered
under this warranty free of charge. Repairs or replacements of products
covered under this warranty are warranted for the remainder of the original
warranty period.
The manufacturer or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service
representatives voids this warranty. The rights under this warranty are limited
to the original user and may not be transferred to subsequent owners.
The warranty is in lieu of all other warranties, expressed or implied,
including warranties of merchantability and fitness for a particular purpose.
Some states do not allow the exclusion or limitations of incidental or
consequential damages, so the above limitations may not apply to you.
Authorized Matco Repair Centers:
United States
Matco Air Tool Repair SV
1330 Commerce Drive
Stow, OH 44224
(800) 433-7098
NMG Industrial WTRC
Attn: South Dock
2223 S. Wilson Street
Tempe, AZ 85282
PRODUCT INFORMATION:
• Innovative design. Up to 1.5" shorter than a traditional
die grinder and allows pressure to be applied directly
over work surface rather than from a handle.
• Universal. 1/4" - 20 male spindle threads into almost
any roll lock holder with 1/4" shank removed.
• Powerful. Inline design of the .4HP motor can even
best .5HP gear transferred right angle die grinders.
SPECIFICATIONS:
Spindle: 1/4"-20 (Male)
Motor: .4 HP
Free Speed: 7,000~19,000 RPM
Air Consumption: 3.1 CFM
Air Inlet: 1/4"
DO NOT DISCARD – GIVE TO USER
Page 1
MT2422
1 YEAR LIMITED WARRANTY
Canada
H. T. Pneumatic Rebuilders Inc.
22 Goodmark Place
Units 7 & 8
Toronto, Ontario M9W6R2
Made in Taiwan
to Matco specifications
Pressure: 90psi
Exhaust: Side, adjustable
Weight: 1.1 lbs.
Length: 3.55"
1604071-14MA