Related Manuals for Cedes cegard/Pro CabSafe 2D
Summary of Contents for Cedes cegard/Pro CabSafe 2D
- Page 1 CabSafe 2D Light Curtain Installation and Operation Manual CEDES AG is certified according to ISO 9001: 2015 English Pages 2 - 14 116 106 en | 200820 | V1.0...
-
Page 2: Table Of Contents
© CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 2/14... -
Page 3: Non-Intended Use
CAUTION Possible health risks Disregarding these notices can lead to damage to the sensor, the door controller and/or other devices. © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 3/14... -
Page 4: Introduction
(Tx) and re- ceiver (Rx) edge and two connection cables. The edges are built with anodized aluminum profiles. The © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 4/14... -
Page 5: Features
Unpack the profiles just before installation in order to avoid damage. ► Do not bend or twist the edges! © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 5/14... -
Page 6: Integration
► Mount the edges on a flat surface ► Do not bend the edges during transport or during the installation. © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 6/14... -
Page 7: Installation Height
(0.39 in.) between the two edges for both: dynamic and static installations. Table 1: Mounting steps © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 7/14... -
Page 8: Electrical Installation
FSSL output signal (see chapter 4.6.4.1). Figure 7: Electrical connection to a CabSafe Controller (n.c. = not connected) © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 8/14... -
Page 9: Fssl Output
DO (dark-on). Both options are in- Figure 11: Configuration of the push-pull output and respective dicated dotted in Figure 10. logic © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 9/14... -
Page 10: Timing Diagram
(from the bottom to the top of the protective field). ► Check the power supply ON/OFF and the connection of the blinking emitter (TX) cable (white connector). © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 10/14... -
Page 11: Maintenance
If a problem persists, please contact your local build the lot number. CEDES representative. Visit www.cedes.com for con- tact data. © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 11/14... -
Page 12: Type Description
(0.75 in.) #10 x ½ in. self drilling 28 (1.1 in.) Figure 14: Vision shield and mounting profiles (dimensions in mm) © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 12/14... -
Page 13: Mounting Clips
24 VDC (pair) Cable durability IEC 60227-2:2003 Max inrush current per < 5 A (< 200 µs) edge RoHS 2011/65/EU © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 13/14... -
Page 14: Dimensions
At the end of life, this equipment should be collected separately from any unsorted municipal waste. Figure 17: Cross section cegard/Pro (CabSafe 2D) light curtain CEDES AG, Science Park | CH-7302 Landquart Phone: +41 81 307 2323 | Fax: +41 81 307 2325 | info@cedes.com | www.cedes.com...
Need help?
Do you have a question about the cegard/Pro CabSafe 2D and is the answer not in the manual?
Questions and answers