Table of Contents
Advertisement
Quick Links
Operating and installation instructions
EWFS Weather station plus
Keep for future use!
Valid from 01 october 2019
Neneral information
1
2
3
Fig. 1
EWFS Weather station plus
1 Heated sensor surface (precipitation sensor)
2 Photodiodes (photo sensor)
3 Wind current sensor (wind sensor)
4 Joint
5 Mounting plate with cover
The connection for the weather station power supply is
found under the cover.
The EWFS Weather station plus enables the wireless con-
trol of sun shading drives and is equipped with sensors
for brightness, wind speed and precipitation. The weather
station is supplied with mains voltage. The device sends
move commands to EWFS-compatible receivers.
Nntended use
The EWFS Weather station plus is an electronic device
developed to control sun shading systems. The approval
of the manufacturer must be obtained for uses outside of
the purposes listed in these instructions.
890464_k•en•2019-10-01
Safety instructions
4
5
Therefore, never place any objects in the area of move-
ment of an automatically controlled mechanism.
Disconnect the power supply of the controlled sun
shading products before maintaining or cleaning the
products.
R
ITNCE
W
WARNRN
The electrical installation must be per-
formed by a certified electrician in accord-
ance with the electrical installation regula-
tions published by the Wssociation of Ner-
man Electrical Engineers (VDE 0100) or the
standards and regulations of the country
in which the device is being installed. The
specialist must observe the installation
instructions included with the electrical
device.
W
WARNRN
Nf hazard-free operation cannot be
assumed, the device may not be commis-
sioned or must be decommissioned.
This assumption is justified,
Nf the housing or the supply lines show
signs of damage,
The device is no longer working.
W
WARNRN
Wn automatically controlled mechanism
may begin to move unexpectedly!
C
WATNIR
Never activate buttons on your transmitter
arbitrarily without visual contact to the sun
shading product. Children may not play with
this product - Remote controls or transmit-
ters may not get into the hands of children!
The receiver (e.g. the radio plug receiver,
radio tubular motor) cannot function in the
event of a power failure. Therefore, raise the
sun shading system early enough in case of
an approaching storm.
We reserve the right to carry out improvements
1
Advertisement
Table of Contents
Related Manuals for WAREMA EWFS Weather station plus
Summary of Contents for WAREMA EWFS Weather station plus
- Page 1 The connection for the weather station power supply is found under the cover. WARNRN The EWFS Weather station plus enables the wireless con- Wn automatically controlled mechanism trol of sun shading drives and is equipped with sensors may begin to move unexpectedly! for brightness, wind speed and precipitation.
-
Page 2: Mounting Plate
The radio control range is limited by legal regulations for Separate spacers are included for wall and ceiling radio systems and by structural factors. Adequate radio installation. They prevent cracking and deformation of reception must be taken into consideration when planning the plastic (Fig. 2). -
Page 3: Wall Mounting
Wall mounting Pole installation Fig. 4 Wall mounting Clip one of the included spacers in the threaded hole (horizontally or vertically, Fig. 2). Attach the weather station to a suitable substructure using the included screws and dowels as shown Fig. 6 Pole installation and steel cable ties locking mechanism (Fig. 4). - Page 4 Connection Iperating elements Fig. 7 Connecting the weather station 1 Cable conduit Fig. 8 Operating elements, view from below, factory setting 2 Strain relief Wind: Wind speed limits can be preselected using this switch. 3 Aubber seal LED: Flashes green when the L button is 4 Terminals pressed.
-
Page 5: Symbols Used
Symbols used Learning in the weather station When the receiver is delivered, it does not "know" any The weather station sends wind-, brightness- and precipita- transmitters initially and first needs to learn to which tion-related move commands to an EWFS Receiver. It must transmitters it should respond. - Page 6 1. Test the wind monitoring function For this function, the wind speed limit may not be set to Move the "Wind" switch on the weather station to the TEST and the brightness limit TEST position. Move the sun shading system down value may not be set to OFF slightly and simulate a gust of wind on the wind sen- at the weather station.
- Page 7 2. Test the sun control Learning in functions individually Move the sun shading system manually to its middle If problems arose when learning in the weather station of a position. sun shading product, the functions can be learned into the sun shading product separately later on.
- Page 8 Learning in the sun control individually Learning in precipitation monitoring individually Perform the following steps consecutively: Perform the following steps consecutively: Place receiver 1 into learn Place receiver 1 into learn mode: Take the hand-held mode: Take the hand-held Ι Ι transmitter into which the transmitter into which the master channel was learned master channel was learned...
- Page 9 Changing the limit values Iperation Switching the sun control on/off temporarily WATNIR ("W" button) Changing these settings may impair the safety of the system or reduce its effective- To temporarily switch off the sun control for a channel into ness. It is better to consult an expert if you which the weather station has been learned in using the W are not sure about the effect of a change.
-
Page 10: Maintenance
Cleaning Liability Photo sensors or solar panels must always be clean Failure to comply with the product information in these to avoid incorrect measuring values and to ensure instructions and use of the device in a manner that con- operating reliability. The device should occasionally be travenes its intended use and purpose may result in the checked for soiling (e.g. -
Page 11: Heartbeat Function
This device meets the requirements on electromagnetic immu- nity and electromagnetic interference for use in residential and commercial environments. WAREMA Renkhoff SE declares herewith that this radio system type [EWFS Weather station plus] is in compliance with the current guidelines. Wmbient conditions Operating and storage °C... -
Page 12: Troubleshooting
Troubleshooting Type of malfunction Possible cause Aemedy The sun shading system does not wave The receiver is not in learn mode Place the receiver into learn mode when the button is pressed (the status No operating voltage at the receiver Switch on the mains voltage LED flashes green while the button is...
Need help?
Do you have a question about the EWFS Weather station plus and is the answer not in the manual?
Questions and answers