Advertisement
Y Y Y Y Y our Curtis
our Curtis
our Curtis ADS System is F
our Curtis
ADS System is F
ADS System is F
ADS System is Factor
our Curtis
ADS System is F
After connection to water and power; the rear toggle switch must be on. You will hear a beep sound, indicating power is available to the controller.
WILBUR CURTIS
The control displays
Water will fill the tank (approximately 2-3 minutes depending on water flow rate). When the proper level is reached
screen. It takes approximately 20 minutes to reach setpoint temperature of 200°F.
WILBUR CURTIS
Control will display
READY TO BREW
T T T T T o Go Into Programming
o Go Into Programming
o Go Into Programming
o Go Into Programming
o Go Into Programming
Turn off (dark display) by pressing ON/OFF
Continue holding BREW
BREW button. Display will read
BREW
BREW
BREW
correspond to the buttons (see illustration below).
1
2
PROGRAM MENUS
During actual brew cycle a
2-minute drip mode is added to
the brew time. The programmed
water level compensates for back
to back brewing in Delta 3 to allow
for an increase of water volume.
T T T T T empera
empera
empera
empera ture (F
empera
ture (F
ture (F
ture (Factor
ture (F
actor
actor
actor
actor y set to 200
y set to 200°F) F) F) F) F)
y set to 200
y set to 200
y set to 200
to Select. Press < < < < < or > > > > > to move to desired temperature and then
Press
Energy Save Mode (Factory set to OFF)
Energy Save Mode (Factory set to OFF)
Energy Save Mode (Factory set to OFF)
Energy Save Mode (Factory set to OFF)
Energy Save Mode (Factory set to OFF)
to Select, < < < < < or > > > > > ON, OFF or ON 140ºF ,
Press
In the ON 140ºF position, temperature goes down to 140ºF. if unit has not brewed in 4 hours. This feature will save energy by not heating the tank during periods of non-operation.
Brew Count Odom.
Brew Count Odom.
Brew Count Odom.
Brew Count Odom.
Brew Count Odom.
Press
to display total brew cycles. Press ex ex ex ex ex or Reset
Pre-Infusion (Factory set to OFF)
Pre-Infusion (Factory set to OFF)
Pre-Infusion (Factory set to OFF)
Pre-Infusion (Factory set to OFF)
Pre-Infusion (Factory set to OFF)
Press
to Select. Current setting in seconds is displayed < < < < < to decrease or select > > > > > to increase (range from OFF to 10 through 60 seconds),
If Pre-infusion is selected (ON), Cold Brew Lock is set to Delta 1 within 5ºF of set point and Cold Brew Lock is dissappears from the list of program selections. When Pre-infusion is ON, Pulse Brew
dissappears from the list of program selections.
Brew Count
Brew Count
Brew Count T T T T T otal
otal
otal
otal
Brew Count
Brew Count
otal
Press
to Select, Shows total gallons and total brew cycles on the unit. Not resettable.
Cold Brew Lock . . . (Factory set to OFF)
Cold Brew Lock . . . (Factory set to OFF)
Cold Brew Lock . . . (Factory set to OFF)
Cold Brew Lock . . . (Factory set to OFF)
Cold Brew Lock . . . (Factory set to OFF)
Press
to select, < < < < < or > > > > > to select desired setting (CBL 5, 15 or OFF),
The Cold Brew Lock feature allows the brewer to brew at three different temperature levels from the actual set point. The first setting is within 5 degrees of set point, next is within 15 degrees of set point, OFF
is within 30 degrees of set point for the Ready to Brew message, however it will brew at any temperature. This feature will operate after initialization to set temperature after the rear standby toggle switch is
reset to ON.
Master Reset
Master Reset
Master Reset
Master Reset
Master Reset
Press
to display Are
Are Y Y Y Y Y ou Sure?
Are
Are
ou Sure?
ou Sure?
ou Sure?
Are
ou Sure?
Then < < < < < for Y Y Y Y Y es es es es es, > > > > > for No No No No No.
Brewer factory defaults are then reset.
Service Call (Phone number Factory set to [800] 995-0417)
Service Call (Phone number Factory set to [800] 995-0417)
Service Call (Phone number Factory set to [800] 995-0417)
Service Call (Phone number Factory set to [800] 995-0417)
Service Call (Phone number Factory set to [800] 995-0417)
Press
to display number and change number or < < < < < to move place and EX to exit when complete This number will be displayed during a Heating system SENSOR ERROR or during a WATER ERROR.
Access Code (Factory set to 1-2-3-4)
Access Code (Factory set to 1-2-3-4)
Access Code (Factory set to 1-2-3-4)
Access Code (Factory set to 1-2-3-4)
Access Code (Factory set to 1-2-3-4)
Press
to display number and change number, (the number can be change 1 to 4) or < < < < < to move place and ex ex ex ex ex to exit when complete.
Banner Name
Banner Name
Banner Name (Factory set to WILBUR CURTIS)
Banner Name
Banner Name
Press
to display letters and change letters or < < < < < to move place and EX EX EX EX EX to exit when complete
This feature allows up to 14 letters to be programmed for company name or regional name. Programming all blanks disables Banner Name. If programmed, Banner Name is displayed every 5 sec. on and off.
P-Maintenance (Factory set to OFF)
P-Maintenance (Factory set to OFF)
P-Maintenance (Factory set to OFF)
P-Maintenance (Factory set to OFF)
P-Maintenance (Factory set to OFF)
Press
to Select, Set gallons brewed to indicate P-Maintenance. Press < < < < < or > > > > > to adjust from Off to 3000 gallons. Press
Beeper On/Off (Factory set to ON)
Beeper On/Off (Factory set to ON)
Beeper On/Off (Factory set to ON)
Beeper On/Off (Factory set to ON)
Beeper On/Off (Factory set to ON)
to display ON or OFF. Pressing either < < < < < or > > > > > toggles between on and off. to set.
Press
2
actor
actory Pre-Set for Optimum P
actor
y Pre-Set for Optimum P
y Pre-Set for Optimum Performance.
y Pre-Set for Optimum P
actor
y Pre-Set for Optimum P
. Press ON/OFF button and the screen will display
when temperature reaches the setpoint (200°F). Unit is now ready to brew.
ON/OFF
ON/OFF
ON/OFF button (yellow). Press and hold BREW
ON/OFF
ENTERING PROGRAM
, wait until
MODE
4
3
Brew Volume (Factory set to 2.2 Liters)
Brew Volume (Factory set to 2.2 Liters)
Brew Volume (Factory set to 2.2 Liters)
Brew Volume (Factory set to 2.2 Liters)
Brew Volume (Factory set to 2.2 Liters)
Selecting Brew by Volume
Brew by Volume or Brew by Time
Brew by Volume
Brew by Volume
Brew by Volume
Brew by Time
Brew by Time
Brew by Time
Brew by Time depends on whether you know your brew time before starting.
From Program Menus press > > > > > display will now show the next feature.
Brew by
Brew by V V V V V olume
Brew by
Brew by
Brew by
olume
olume
olume
olume: Press
to Select, Display will now show Push START To Begin... Press the BREW
volume is reached press BREW
BREW
BREW
BREW
BREW button again to stop the flow. Now the volume has been set. Pressing > > > > > button will display the subsequent menu features.
Next item in the sequence is Brew by Time.
Brew by Time.
Brew by Time.
Brew by Time. Press
Brew by Time.
toggle back and forth from minutes to seconds to exit (ex). Change the time or set and exit by pressing .
to set. Temperature is programmable from 170ºF to 204ºF in 2-degree increments.
to set. When in ON, unit will automatically shut off 4 hours from last brew. When feature is OFF, unit does not have the energy saving mode.
to set.
erformance.
erformance.
erformance.
erformance.
<Airpot Brewer>
. After three seconds,
WILBUR CURTIS
BREW
BREW
BREW
BREW button (green) and then press and release ON/OFF
ENTER CODE
is displayed Enter the 4-digit access code, the digits 1-4
– – – –
The default code set at the factory is 1-2-3-4. Then
displayed.
All programming selections are performed with the three center buttons.
The symbols below the buttons are:
Scroll LEFT
SELECTION or ENTER to save new parameter
Scroll RIGHT
to Select to change the brew time. Display will now show the current time. By pressing < < < < < or > > > > > you can
to exit.
D500 GT
WILBUR CURTIS
is displayed.
FILLING
WILBUR CURTIS
will appear on the
HEATING
ON/OFF
ON/OFF
ON/OFF
ON/OFF button (yellow).
PROGRAM MENUS
<
SELECT
>
BREW
BREW
BREW button then hot water starts running, when desired
BREW
to set.
will be
Advertisement
