Jindara Opal Installation Instructions

ZCC Part No. 225333
E
30
Hearth Width
Clearance to combustibles
MODEL
Opal
Riverina
Stockade
Barossa
Kimberley
Hamersley
Federation
Victorian
Installation notes:
The Gason Zero Clearance Cabinet is an approved cabinet that allows for Eureka/Jindara Insert woodheaters as stated above to be installed within
replace in accordance with AS2918:2001.
This can be achieved by following the installation guidelines listed below.
• Select the position that you wish to to install your ZCC , car
being 255mm requires a 25mm clearance on either side to combustibles, making overall clearance 305mm).
• (non-combustible cement sheet, villaboard or similar) in the position desired for the ZCC, ensuring hearth will
extend fully underneath ZCC as shown above for relevent model. Place the ZCC into position.
• the ZCC . Note: Line up centre holes with corresponding holes depending on model. Refer to diagram on sheet 2.
• Fit the to the upstands and terminate at the required height above the roof line.
• Fit 300mm x 100mm vermin proof vent directly behind where the
allow air access to the zero box either from another room or external air. Note, if installed on
required. i.e. Either thr
• Build your frame around the ZCC
• Cover the front face of framing with a minimum 4mm cement sheet or non-combustible material.
• Cover the rest of the frame to suit your requirments with plaster, timber, MDF etc.
• Insert your chosen appliance into the zero cabinet. Note: x2 galvanized c-section brackets supplied are required to centralise
Opal/Riverina, Stockade/Barossa. For installation of Kimberley, Hamersley, Federation and Victorian, appliances must sit on c-section
to ensure correct installation height is achieved. Fit active ue and cowl once appliance is in position.
• Install the mantel if required. Note if mantle is made out of a combustible material the following dimensions must be adhered to.
All dimensions are minimum and must under no circumstances be reduced.
interpretation of AS2918:2001.
Stockade SRS5, Barossa SRS3, Kimberley Mk2, Hamersley Mk2
Tripleskin
Flue
690
660
836
C
A B C D
12 570 890 810
12 570 890 810
12 550 950 810
12 550 950 810
18 615 940 1063
18 705 1000 1063
18 705 1000
1063
18 705 1000 1063
r, one each side of the zero box, or alternatively, through the side wall(s), if applicable.
mantaining the clearances listed above.
Compact Zero Clearance
Cabinet Installation
To suit Insert models: Opal SRS4, Riverina SRS3,
Federation Mk2 & Victorian Insert
NOTE:
A min. 60mm gap for
Opal SRS4/Riverina SRS3
and 120mm gap for
Stockade SRS5/Barossa SRS3
timber stud.
The timber stud may need
to be notched out to allow
for the minimum required
D
763
B
A
All dimensions in millimetres, images not to scale
E F G H
40 20 1040 1100 50
40 20 1040 1100 50
40 20 1340 1390 50
40 20 1340 1390 50
100 50 1050 1140 25
100 50 975 1225 150
100 50 975 1225 150
100 50 975 1225 150
See oversheet for dimensions.
ZCC
will be located, as near as practicable to the
A. F. Gason Pty Ltd accepts no liability whatsoever for their
Zero
Clearance
Box
545
Hearth depth
I J
mm in front
of unit
250 530
250 530
250 510
250 510
250 550
250 600
250 600
250 600
roof cavity (The outer
r. This vent will
r, an additional two vents are
F