Metal Part cal return path to the chassis. Any current measured must not exceed 0.5mA. Reverse the instrument power cord plug in the out- ohmmeter let and repeat the test. See Fig. 1-1. Fig. 1-2 Insulation Resistance Test Samsung Electronics...
Page 4
(5) antenna wiring. Always inspect in all areas tinuously and new instructions are issued whenev- for pinched, out-of-place, or frayed wiring, Do not er appropriate. change spacing between a component and the printed-circuit board. Check the AC power cord for damage. Samsung Electronics...
Components identi- fied by shading, by( ) or by ( ) in the circuit dia- gram are important for safety or for the characteris- tics of the unit. Always replace them with the exact replacement components. Samsung Electronics...
(6) Do not remove a replacement ESD device from its protective package until immediately before your are ready to install it.(Most replacement ESD devices are packaged with leads electrically short- ed together by conductive foam, aluminum foil or comparable conductive materials). Samsung Electronics...
◆ Be sure to put on a wrist strap grounded to the sheet. ◆ Be sure to lay a conductive sheet made of copper etc. Which is grounded to the table. Samsung Electronics...
For DVD discs, audio signals recorded at 96 kHz sampling frequency are converted into and output at 48 kHz. Disc Type AUDIO CD(CD-DA) Analog Audio Output 48 / 96 kHz 44,1 kHz Digital Audio Output 48 kHz 44,1 kHz Samsung Electronics...
Page 10
Product Specification DVD-SR150M is SAMSUNG 4th DVD Recorder with Built in Set-Top Box(STB). Built-in STB Module supply for Digital terrestrial Television Reception in European Area. And DVD-SR150M have DV input terminal which can record camcorder signal. - Both Digital Television and also Radio Reception...
Product Specification 2-2 Chassis Product Specification General Model Name DVD-R155 DVD-SR150M Design (Type Name) VR-7147 VR-7253 Remocon Code SEC-SINGLE SEC R-SINGLE 8Button 47Key 53Key REMOTE Battery Type CONTROLLER Body Color Black Black Language English English Multi-Brand TV Control Illuminated Button...
Page 12
Product Specification General Model Name DVD-R155 DVD-SR150M PLAYABLE Memory Card MEDIA & Hard Disc (HDD) FORMAT VHS Tape DVD-RAM DVD-RW DVD-R DVD+RW Recording DVD+R Media CD-R CD-RW DUAL LAYER RECORDING Yes(-R) Hard Disc (HDD) VHS Tape VIDEO MPEG-2 MPEG-2 AUDIO...
Page 13
Product Specification General Model Name DVD-R155 DVD-SR150M Video DAC 10bit/54MHz 10bit/54MHz Progressive Scan Output Yes(576p) VIDEO Component Video Output RGB Output with Scart AV 1 OUTPUT HDMI Output HDMI - Upscaling(720P/1080i) 576p/720p/1080i Audio DAC 24bit/96kHz 24bit/96kHz Dolby Digital Out AUDIO...
Page 14
Product Specification General Model Name DVD-R155 DVD-SR150M Remote Controller Batteries Yes(x2) Yes(x2) AV Cable (RCA Type) RF Cable Euro Scart Cable HDMI - HDMI Cable ACCESSORY HDMI - DVI Cable User's Manual (Instruction Manual) Quick Start Guide DISC ( Bundle )
Product Specification 2-3 Option Product Specification Description Fig Description Parts No Remark Remote Model Standard of AK59-00062S Control DVD-SR150M/XEU Model Standard of Batteries for 4301-001035 DVD-SR150M/XEU Remote Control S.N.A Model Standard of AK68-01434A User’s Manual DVD-SR150M/XEU Model Standard of Quick Guide...
2) Lift up the Top Cabinet in direction of arrow. ´ 1 SCREW (3 x 10 B) Œ 3 SCREWS (3 x 10 B) TOP CABINET ˇ 1 SCREW (3 x 10 B) Fig. 3-1 Top Cabinet Removal Samsung Electronics...
Page 19
3-1-3 Ass’y Deck Removal 1) Remove 4 Screws Œ, ´ from the Ass’y Deck and lift it up. Œ 2 SCREWS ´ 2 SCREWS (3 x 8 W) (3 x 10 W) ASS’Y DECK Fig. 3-3 Ass’y Deck Removal Samsung Electronics...
Page 20
2) Remove 5 Screws ˇ,¨ from the S.M.P.S PCB and lift it up. ˇ 2 SCREWS (3 x 6 W) ¨ 3 SCREWS (3 x 10 W) ´ 2 SCREWS S.M.P.S PCB (3 x 10 W) MAIN PCB Fig. 3-4 Main PCB, and S.M.P.S PCB Removal Samsung Electronics...
Page 21
3) Remove 2 Screws ˇ, from the DC fan and lift it up. ´ 3 SCREWS (3 x 6 W) Œ 4 SCREWS (3 x 6 W) FRONT PCB JACK PCB DC FAN ˇ 2 SCREWS (5 x 14 Y) Fig. 3-5 Jack PCB, Front PCB and DC Fan Removal Samsung Electronics...
Is there Œ Check 2st voltage voitage at pin "1"(Draing)of ´ Check 1st short circuited or ICIS01 opened parts Refer to wave pattern image of Fig. 4-1 Operation of ICIS01 is Replace ICIS01 Normal? Check feed back ICIS01 Samsung Electronics...
Page 26
About P-P1V appears at IC216 and output jack Output jack? Refer to wave pattern image of Fig. 4-4 Check the RCA cable # IF Recorder is under PSO(progressive scan output) MODE, it does not output the CVBS& S-Video, RGB signal. Samsung Electronics...
Page 29
Trouble Shooting Pin34 Pin30 CVBS Output Jack (Color-Bar) Output Jack Jack PCB Page, 6-7 Output Jack IO (Jack PCB) Page, 7-17 Fig. 4-4 Samsung Electronics...
Page 30
About P-P1V appears at IC216 and output jack Output Jack? Refer to wave pattern image of Fig. 4-7 Check the RCA cable # IF Recorder is under PSO(progressive scan output) MODE, or it does not output the CVBS& S-Video signal. Samsung Electronics...
Page 33
Output Jack Pr Y-Color bar Output Jack Pb Output Jack Y Pb-Color bar Jack PCB Page, 6-7 Pr-Color bar Œ ´ ˇ Output Jack Y Output Jack Pb Output Jack Pr IO (Jack PCB) Page, 7-17 Fig. 4-7 Samsung Electronics 4-11...
Page 34
Refer to wave pattern image of Fig. 4-9 Video signals Check the connection between of about P-P1V appears at IC216 and output jack output jack? Refer to wave pattern image of Fig. 4-10 Check the S-Video cable 4-12 Samsung Electronics...
Page 37
Trouble Shooting Pin34 Pin30 Y-Color bar SJACK5 C Out C-Color bar SJACK5 Y Out Jack PCB Page, 6-7 SJACK5 C Out SJACK5 Y Out IO (Jack PCB) Page, 7-17 Fig. 4-10 Samsung Electronics 4-15...
Page 38
IC216 and output jack AV1 output jack? Refer to wave pattern image of Fig. 4-13 Check the RCA cable # IF Recorder is under Component mode (in OSD setup menu), it does not output RGB out put. 4-16 Samsung Electronics...
Page 42
IC216(pin30, 34) and PCN1 (10,11) Refer to wave pattern image of Fig. 4-15 CN3 pin (14,16,18) of Jack PCB or CON2 of Main PCB has normal level? Refer to wave pattern image of Fig. 4-15 Check Main PCB 4-20 Samsung Electronics...
Page 45
12pin of CN3 of Check the connection between Jack PCB or CON2 of Main PCB 12pin of CN3 of Jack PCB and has normal level? pin 35 in IC216 Refer to wave pattern image of Fig. 4-17 Change Main PCB Samsung Electronics 4-23...
Page 48
ChecK Digital Replace Main PCB Audio data PIN 30 of CON2 (Main PCB) Refer to wave pattern image of Fig. 4-18 Check 5V SJACK3 Replace SJACK3 Refer to wave pattern image of Fig. 4-18 Check the Cable 4-26 Samsung Electronics...
Page 49
Trouble Shooting Œ Œ Main PCB Page, 6-5 BB_Connector (Jack PCB) Page, 7-18 ´ ´ Jack PCB Page, 6-7 IO (Jack PCB) Page, 7-17 Œ Œ Digital Audio Data ´ ´ Pin2 (SJACK3) Fig. 4-18 Samsung Electronics 4-27...
Page 50
VIC1 3.3V Replace Main PCB (Main PCB) Check output I2S singnal of audio DAC (VDR23, Replace Main PCB VDR43,VDR24,VDR44) Refer to wave pattern image of Fig. 4-21 Check the passive parts around jack pin. 4-28 Samsung Electronics...
Page 53
´ PCMIO XCLK Main PCB Page, 6-4 ˇ ¨ ˆ ´ Video Decoder (Main PCB) Page, 7-9 Œ Video Decoder (Main PCB) Page, 7-9 ˇ ˇ PCMO BCK ¨ ¨ PCMO LRCLK ˆ ˆ PCMO Data Out Fig. 4-21 Samsung Electronics 4-31...
Page 54
(Main PCB) Refer to wave pattern image of Fig. 4-22 Check I2S Replace Main PCB singnal of audio ADC (VDR56) Refer to wave pattern image of Fig. 4-23 Check connection between Main connector CON1,CON2,CON3 and Jack connector CN3,CN4,CN5 4-32 Samsung Electronics...
Page 57
Is the 40pin FFC cable(betweenmain & deck) Reinsert FFC cable correctly inserted correctly? Is the waveform Change the Main board of DECKCN pin1 normal? (Main PCB) Refer to wave pattern image of Fig. 4-24 Change the deck Samsung Electronics 4-35...
Page 59
FIC1. Refer to wave pattern image of Fig. 4-25 Video output Replace TM (tuner) block. signal of Tuner is OK? (jack PCB) Refer to wave pattern image of Fig. 4-26 Refer to AV3 Video line error Samsung Electronics 4-37...
Page 62
Check the SIF signal or tuner from11pin of tuner is OK? Refer to wave pattern image of Fig. 4-26 If Audio R/L signal Pin 107 and 105 of VIC1is normal, refer to AV3 Audio Line in error 4-40 Samsung Electronics...
Page 63
OK? (Key PCB) of ARM1 is 5V. Refer to wave pattern image of Fig. 4-27 FIC1(58pin) signal Check between FIC1(58pin) is OK? (Jack PCB) and ARM1(1pin). Refer to wave pattern image of Fig. 4-27 Change AIC1 or around elements Samsung Electronics 4-41...
Page 64
Trouble Shooting Œ Œ Display key (FUNCTION PCB) Page, 7-19 Front AV PCB Page, 6-11 ´ ´ Jack PCB Page, 6-7 System Control (Jack PCB) Page, 7-13 Œ Œ ,´ ´ ARM1 Pin1 and FIC1 Pin58 Fig. 4-27 4-42 Samsung Electronics...
Page 65
Pin 3 : 5V Pin 5 : 30V Pin 12 : 3.3V Refer to wave pattern image of Fig. 4-28 Check the short circuit or passive componets arround Tuner of JACK PCB and DIC6 of MAIN PCB Samsung Electronics 4-43...
4-2 Software Update 4-2-1 Drive Firmware Update 4-2-1-a Introduction Samsung will often support the software update to improve the performance of DVD Recorder&VCR to the latest status, through Samsung Internet Site. (http://europe.samsungportal.com) 4-2-1-b How to make an update disc • Write the downloaded file onto a blank CD-R or CD-RW disc, using the following settings : 1) You have to download a newly file through Samsung Internet Site.
Page 68
And then do not turn off the unit until it goes off automatically. Drive Update Drive firmware is successfully updated. Fig. 4-17 6) After removing the update disc, turn off the unit with power button. Finally, the Drive Firmware update is ended. 4-46 Samsung Electronics...
Page 69
Trouble Shooting 4-2-2 Flash Update (Main PCB) 4-2-2-a Introduction Samsung will often support the software update to improve the performance of DVD Recorder&VCR to the latest status, through Samsung Internet Site. (http://europe.samsungportal.com) 4-2-2-b How to make an update disc Write the downloaded file onto a blank CD-R or CD-RW disc, using the following settings : 1) Download the software update file from the Samsung internet site.
Page 70
The message below will be displayed in the screen after update is completed and the tray will open automatically. Flash Update Flash memory is successfully updated. Fig. 4-21 6) After removing a update disc, turn on the unit with power button. the Flash update is ended. 4-48 Samsung Electronics...
Exploded Views and Parts List 5-1 Cabinet Assembly W200 W004 W001 W001 W004 H001 W275 P001D C015 W001 W275 W275 P0055 P030 W004 W271 P022 P025 P003 A001 W202 C001 P005 C002 This Document can not be used without Samsung’s authorization Samsung Electronics...
Page 73
ASSY PCB-FUNCTION;DVD-HR755,HDD & P022 AK92-01499A ASSY PCB-JACK;DVD-SR150M,Nexus,R- P025 3903-000175 CBF-POWER CORD;AT,GB,GP2,HOUSING( P030 3103-001158 FAN-DC;12V,20mA,2000rpm,0.125m^3/ W001 6003-000275 SCREW-TAPTITE;BH,+,-,B,M3,L10,ZPC W004 6003-000283 SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC( W200 6003-001375 SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC( W271 6009-001411 SCREW-SPECIAL;TH,+,-,M5,L14,NI PL W275 6003-001561 SCREW-TAPTITE;BH,+,-,B,M3,L6,ZPC( This Document can not be used without Samsung’s authorization Samsung Electronics...
3) LIS01, LISO2, CIS04, CIS05 : Noise removal at power input/output. 4) RIS04 : Rush current limit resistance at the momemt of power cord insertion. · Without PLRU1, the bridge diode might be damaged as the rush current increases. Samsung Electronics This Document can not be used without Samsung’s authorization.
Page 104
Smoothing Circuit VoltageCircuit (x3) 12V Rectified 12V Rectified Smoothing Circuit VoltageCircuit (X2) PWM Control Circuit Line Filter (ICE2B765) 3.3V Rectified Voltage Smoothing Circuit Detection Circuit Power IN (230V) Fig. 7-4 This Document can not be used without Samsung’s authorization. Samsung Electronics...
Schematic Diagrams 7-4 Main Connector (Main PCB) Power Audio Video This Document can not be used without Samsung’s authorization. Samsung Electronics...
Schematic Diagrams 7-5 ATAPI (Main PCB) Power Œ Œ ◆ These are the waveforms of DVD-SR150M. Œ Flash CS5 Caution There can be some differences (Voltage, Frequency, stc.) among cameras. Samsung Electronics This Document can not be used without Samsung’s authorization.
7-6 Main Codec (Main PCB) Power Audio Video ´ DDR Clock Œ ◆ These are the waveforms of DVD-SR150M. Caution There can be some differences (Voltage, Frequency, stc.) among cameras. This Document can not be used without Samsung’s authorization. Samsung Electronics...
Ø ¨ PCMO Data Out ˆ PCMIO XCLK Ø VIN CLK ◆ These are the waveforms of DVD-SR150M. Caution There can be some differences (Voltage, Frequency, stc.) among cameras. Samsung Electronics This Document can not be used without Samsung’s authorization.
7-9 DV Interface (Main PCB) Power Œ DV IN CLK Œ ◆ These are the waveforms of DVD-SR150M. Caution There can be some differences (Voltage, Frequency, stc.) among cameras. Samsung Electronics This Document can not be used without Samsung’s authorization. 7-11...
Schematic Diagrams 7-14 IO_Switching (Jack PCB) Power Audio Video 7-16 This Document can not be used without Samsung’s authorization. Samsung Electronics...
ˇ ˇ 12C Data ¨ SPDIF HDMI ˆ VOut Clock ◆ These are the waveforms of DVD-SR150M. Caution There can be some differences (Voltage, Frequency, stc.) among cameras. Samsung Electronics This Document can not be used without Samsung’s authorization. 7-17...
Schematic Diagrams 7-16 BB_Connector (Jack PCB) Power Audio Video 7-18 This Document can not be used without Samsung’s authorization. Samsung Electronics...
Schematic Diagrams 7-18 Power LED (FRONT PCB) Power Audio Video 7-20 This Document can not be used without Samsung’s authorization. Samsung Electronics...