New England Arbors Cottage Picket Wings Assembly Instructions

Advertisement

Quick Links

A S S E M B LY I N S T R U C T I O N S
Cottage Picket Wings
39"
5"
Please read through before starting assembly.
Check Box for These Contents (1 Box)
In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
1. Posts (2) 4"x 4" x 54" - 10126
2. Top Rails (2) 2" x 3.5" x 44.5" - 10103
3. Bottom Rails (2) 2" x 3.5" x 43.5" - 10104
4. Pickets (4) .875" x 3" x 29.25" - 10105
Pickets (2) .875" x 3" x 30" - 10107
Pickets (2) .875" x 3" x 31.5" - 10108
Pickets (2) .875" x 3" x 32.75" - 10109
Pickets (2) .875" x 3" x 34.25" - 10110
Pickets (2) .875" x 3" x 36.25" - 10111
Pickets (2) .875" x 3" x 38.25" - 10112
Pickets (2) .875" x 3" x 41" - 10113
5. External Post Caps (2) 4" x 4" - 10735-1
6. Post Trim Caps (2) 4" x 4" - 10737-1
7. Base Moldings (2) 5" x 5" - BM20022
8. Rail Mount Brackets (8) 2" x 3.5" - 10045
Hardware Kit (Includes):
9. Self-tapping stainless Screws (32) .625" - 20016
10. Rail end spacers (2) 2" x 3.5" x .5" - 10217
11. Tube of vinyl cement (1) - 20000

Tools You Will Need

• Cordless Drill with #2 Phillips bit
• Tape measure
• Pencil
• Level
• Shovel
• Two bags of pre-mix concrete (optional)

General Information

• Read Instructions through carefully before beginning assembly.
• When handling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 5'x 5' for unobstructed handling.
8"
5"
49"
44"
18.75"
4
6
5
1
2
3
www.newenglandarbors.com
7
8
11
9
10
Not to Scale
V2.4/091916
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Cottage Picket Wings and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for New England Arbors Cottage Picket Wings

  • Page 1 A S S E M B LY I N S T R U C T I O N S Cottage Picket Wings www.newenglandarbors.com 44" 39" 18.75" 8" 5" 5" 49" Please read through before starting assembly. Check Box for These Contents (1 Box) In the event of missing or defective parts please call our customer service dept.
  • Page 2 Cottage Picket Wings Installation S T E P O N E Lay out one of the posts (part 1). Measure 8” from one end of the post and put a mark. Center the rail mount bracket (part 8) on the post, with the open end at the 8”...
  • Page 3 29 1/4” pickets at the post. Make sure the tabs on the end of the pickets “snap” into the bottom rail. Open the second bundle of pickets and repeat for the opposite wing panel. The Cottage Picket Wings...
  • Page 4 Using the distances shown, mark out each hole location on both sides of the arbor. Dig out two 16” deep holes. 1/2” Filler (used when no base trim is present on the arbor post). Ground Level 42" 15.5" 49" The Cottage Picket Wings...
  • Page 5 Vinyl glue is to be applied S T E P F O U R below the picket level. Lower the wing post into the hole, while slipping each rail end into the corresponding bracket on the arbor post. check the top rail for level, and adjust the depth of the hole if needed.

Table of Contents