Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Sync Ergonomics Manuals
  4. Exercise Bike
  5. Project 0.2 Evo
  6. Setup manual

Sync Ergonomics PROJECT 0.2 EVO Setup Manual

Hide thumbs Also See for PROJECT 0.2 EVO:

Advertisement

Quick Links

Download this manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the PROJECT 0.2 EVO and is the answer not in the manual?

Questions and answers

Related Manuals for Sync Ergonomics PROJECT 0.2 EVO

Summary of Contents for Sync Ergonomics PROJECT 0.2 EVO

  • Page 2 Improper assembly of any of the components of EVO could cause damage to the product(s) and/or bicycle, may lead to loss of control of the bicycle, and may lead to personal injury, or in severe cases ev en death. Sync Ergonomics assumes no responsibility for improper assembly and installation of the product(s).
  • Page 3 WARNING: Do not attempt to modify your Sync components, outside of what is described within this setup guide as appropriate for assembly. Modification may impact the structural integrity of a components and could result in component failure, or failure of the complete system. Sync Ergonomics is not liable...
  • Page 4 SYN-EVO-CL-M5-32.5-15 EVO Giant Clamp SYN-EVO-TC-M3-00 EVO Clamp Top Cap EVO Clamp Top Cap Screws SYN-EVO-EX-3XX-25-RX Low Rise Extension (R) SYN-EVO-EX-3XX-25-LX Low Rise Extension (L) Clamp Grub Screws SYN-OPT-CP-15-14-CB Deep Groove Arm Cup Arm Cup Countersunk Screw SYN-OPT-PD EVA Foam Pad SYN-EVO-BR-M5-32.5-132 EVO Giant Brace SYN-EVO-CA-M5-32.5...
  • Page 5 Please ensure that your Giant Trinity Base Bar is complete with the 5 mm bolt spacers inserted into the bolt holes. These parts are supplied with your Giant Trinity and prevent crushing of the base bar when tightening bolts. Do not proceed with assembly without these spacers installed.
  • Page 6 Sync spacers are designed to replace the Giant OEM Spacers. Your EVO Ecosystem is supplied with 40mm of spacers to allow you achieve the perfect fit. If you require additional spacers, please contact us at www.syncergonomics.com. If you are already using the Project 0.2 ecosystem, determine the number of spacers you need by measuring the length of the bolt you currently use and subtract 40 mm.
  • Page 7 Bar Adapter + Clamp Adapter + Clamp Bar Adapter + Clamp Adapter + Clamp Bar Adapter + Clamp Adapter + Clamp Bar Adapter + Clamp Adapter + Clamp Bar Adapter + Clamp Adapter + Clamp Bar Adapter + Clamp Adapter + Clamp Bar Adapter + Clamp Adapter + Clamp It is important to note that your assembly must consist of no less than the Bar Adapter, Clamp Adapter and EVO Clamp.
  • Page 8 You have been provided with a set of Giant Trinity Advanced Pro EVO Extension Clamps. Do not attempt to install the Giant-specific EVO Clamp on a bike other than a Giant Trinity Advanced Pro. We recommend the application of MOTOREX Bike Grease for the clamp bolts. Once you have aligned the Bar Adapter and Aero Spacers with your base bar, place the provided clamp adapter on top of your spacer stack followed by the Giant EVO Brace.
  • Page 9 WARNING: DO NOT DRILL OR MODIFY extensions for cable entry/exit, Low Rise 3D extensions are designed to work with Shimano SW-R9160 and SRAM eTap CLICS only. Any such modification immediately voids the product warranty. Sync Ergonomics is not liable for product damage and/or personal injury resulting...
  • Page 10 When cut to the correct length and height, secure the extensions in the extension clamps with the two grub screws provided (pre-inserted into the clamps). We recommend the application of a light textured carbon paste between the extension and the inside of the clamp to ensure a secure fit.
  • Page 11 Thanks to the connection at the shifter, you can run the Di2 wires through the spacer stack during assembly, leaving sufficient length to connect the shifters as a final step. The wires will run through the spacers, into the clamp and up and out of the extensions. Install your TT grips before finally affixing your shifters in place.
  • Page 12 Sync Ergonomics online store and can be purchased separately when worn out. WARNING: Over torqueing the cup connection screws will lead to permanent damage of the arm cup base plate. Sync Ergonomics is not liable for product...
  • Page 13 For riders seeking a UCI-compliant position, Low Rise 3D Extensions can be trimmed to achieve the desired length and height. Low Rise 3D extensions are designed to be capable of providing 100 mm of height gain, measured from the centre of the arm cup pad, to the top edge of the shifter body.
  • Page 14 Saddle offset 0-50 mm behind the bottom bracket Saddle offset 50 mm (or more) behind the bottom bracket Athlete height of 190 cm or taller, with a saddle offset of 50 mm (or more) behind the bottom bracket The clamp end of the extension must be trimmed in order to achieve UCI compliance for length.