Advertisement
Quick Links
Advertisement
Related Manuals for Keysight Technologies UXG X-Series
Summary of Contents for Keysight Technologies UXG X-Series
- Page 1 Keysight UXG X-Series Agile Signal Generators Add Option AT2 (Attenuator) Kit Part Numbers: N5191-60501 - For Option 520 and 52E N5191-60502 - For Option 540 and 54E N5191-60503 - For Option 520 and 52E, 1EM N5191-60504 - For Option 540 and 54E, 1EM...
- Page 2 The information contained in this document is subject to change without notice. Keysight Technologies makes no warranty of any kind with regard to this material, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
- Page 3 Estimated Verification Time: ....Option 520/52E = 8 hours Option 540/54E = 15 hours Introduction This upgrade kit adds Option AT2 (Attenuator) to the UXG X-Series Agile Signal Generators. Installation includes the following major steps: 1. Check signal generator functionality, page 2.
-
Page 4: Installation Kit Parts List
Table 1 N5191-60501, for Option 520/52E Quantity Description Part Number UXG X-Series Agile Signal Generators Add AT2 to Option 520/52E this note and 540/54E Installation Note Output Leveling Assembly Option AT2/520 N5191-60370 Cable, RF, Semi-Rigid, Mod Filter Output to Coupler Input, Option... -
Page 5: Safety Considerations
Add Option AT2 (Attenuator) Upgrade Kit Tools Required — TORX T-10 driver — TORX T-15 driver — TORX T-20 driver — 5/16” open-ended wrench — Needle-nose pliers — Scissors Safety Considerations Before you disassemble the instrument, turn the power switch off and unplug the signal generator. -
Page 6: Check Signal Generator Functionality
Add Option AT2 (Attenuator) Upgrade Kit Check Signal Generator Functionality Use the following procedure to confirm that the signal generator powers up and the internal check identifies no errors. The internal check evaluates the operation of the signal generator and returns an error message if it detects a problem. - Page 7 Remove the Outer and Inner Bottom Rear Cover Remove the Outer and Inner Bottom Rear Cover Remove the Outer Cover Refer to Figure 1. Disconnect the power cord. 2. Using a T-20 driver, loosen the screws (1) and remove the strap handles (2) from both sides of the instrument.
- Page 8 Remove the Outer and Inner Bottom Rear Cover Remove the Inner Bottom Rear Cover Refer to Figure 1. Place the signal generator upside down. 2. To remove from the rear bottom cover (1), use a T-10 driver to remove the twelve screws (2) (including two on the rear panel).
- Page 9 Installing Option AT2 Installing Option AT2 Remove Existing A20 Output Leveling Assembly 1. For Option 520/52E instruments, refer to Figure For Option 540/54E instruments, refer to Figure For Option 520/52E 1EM instruments, refer to Figure For Option 540/54E 1EM instruments, refer to Figure 2.
- Page 10 Installing Option AT2 Figure 4 Option 540/54E - Remove Existing A20 Output Leveling Assembly (Front Panel RF Output) Installation Note N5191-90020...
- Page 11 Installing Option AT2 Figure 5 Option 520/52E 1EM - Remove Existing A20 Output Leveling Assembly (Rear Panel RF Output) Installation Note N5191-90020...
- Page 12 Installing Option AT2 Figure 6 Option 540/54E 1EM - Remove Existing A20 Output Leveling Assembly (Rear Panel RF Output) Installation Note N5191-90020...
- Page 13 Installing Option AT2 Install A20 Output Leveling Assembly with AT2 Attenuator 1. For Option 520/52E instruments, refer to Figure For Option 540/54E instruments, refer to Figure For Option 520/52E 1EM instruments, refer to Figure For Option 540/54E 1EM instruments, refer to Figure 2.
- Page 14 Installing Option AT2 Figure 7 Option 520/52E Instruments - Install A20 Output Leveling Assembly with AT2 Attenuator (Front Panel RF Output) Installation Note N5191-90020...
- Page 15 Installing Option AT2 Figure 8 Option 540/54E Instruments - Install A20 Output Leveling Assembly with AT2 Attenuator (Front Panel RF Output) Installation Note N5191-90020...
- Page 16 Installing Option AT2 Figure 9 Option 520/52E 1EM Instruments - Install A20 Output Leveling Assembly with AT2 Attenuator (Rear Panel RF Output) Installation Note N5191-90020...
- Page 17 Installing Option AT2 Figure 10 Option 540/54E 1EM Instruments - Install A20 Output Leveling Assembly with AT2 Attenuator (Rear Panel RF Output) Installation Note N5191-90020...
- Page 18 Activate Option AT2 Activate Option AT2 1. Turn the signal generator on and allow it to warm up for 5 minutes. 2. Follow the instructions on the Entitlement Certificate to redeem Option AT2. 3. Connect the instrument to the LAN and write down the IP address. 4.
- Page 19 Verify Proper Installation of Option AT2 Verify Proper Installation of Option AT2 1. Press: System > Instrument Info > Options Info. 2. Make sure Option AT2 is listed. If you enable an option that does not have the required hardware installed, the menus for that option will be activated but the option cannot operate.
- Page 20 Re-Assembling the Instrument Re-Assembling the Instrument Refer to Figure 1 Figure 1. Reinstall the inner bottom rear cover and outer instrument cover by reversing the order for removal. 2. Torque all T-10 screws to 9 in-lbs. 3. Torque all T-20 screws to 21 in-lbs. 4.
-
Page 21: Verify Signal Generator Calibration
Verify Signal Generator Calibration Verify Signal Generator Calibration 1. Turn the signal generator on and allow it to warm up for 45 minutes. 2. Perform the following adjustment and performance tests, in the order listed, to verify signal generator calibration. Refer to the UXG Family Signal Generators Service Software. For Serial Prefixes <... - Page 22 This information is subject to change without notice. © Keysight Technologies 2017 Edition 1, March 2017 N5191-90020 www.keysight.com...