Download Print this page
LG PC100 Easy Setup Manual
LG PC100 Easy Setup Manual

LG PC100 Easy Setup Manual

Mini-pc for signage

Advertisement

Quick Links

Easy Setup Guide
Mini-PC for Signage
PC100/PC200/PC700
Please read this guide carefully before using this product and keep it for future reference.
Please record the model number and serial number of the product on this guide. You will
need to provide this information (if applicable) when you require service.
Safety Precautions
Please read these safety precautions carefully before using the product.
■ Make sure to connect the power cable a grounded outlet.
- You may be electrocuted or injured.
■ Use the rated voltage only.
- The product can be damaged, or you may be electrocuted.
■ During a thunder or lightning storm, unplug the power cable or signal cable.
- You may be electrocuted or a fire can break out.
■ Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered
with dust, dry the power plug completely or wipe dust off.
- You may be electrocuted due to excess moisture.
■ Do not insert a conductor (like a metal chopstick) into one end of the power cable while
the other end is connected to the input terminal on the wall. Additionally, do not touch the
power cable right after plugging into the wall input terminal.
- You may be electrocuted.
■ The appliance coupler is used as the disconnect device.
■ Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
Installation Environment of Mini-PC for Signage
Leave at least 10 cm of space at each side of the product from an obstacle when installing
the product to ensure sufficient ventilation.
10 cm
10 cm
< Install Mini-PC for Signage Attached
to Monitor >
*MFL69325402*
10 cm
10 cm
10 cm
10 cm
< Install Mini-PC for Signage>
P/NO. : MFL69325402(1506-REV00)
10 cm
10 cm
Printed in Korea

Advertisement

loading

Summary of Contents for LG PC100

  • Page 1 Easy Setup Guide Mini-PC for Signage PC100/PC200/PC700 Please read this guide carefully before using this product and keep it for future reference. Please record the model number and serial number of the product on this guide. You will need to provide this information (if applicable) when you require service.
  • Page 2 Note ● SuperSign software and manual. - Downloading from the LG Electronics website. - Visit the LG Electronics website (http://www.lgecommercial.com/supersign) and download the latest software for your model. (Depending on the model, this feature may not be supported.)
  • Page 3 PC100 Monitor Integration We recommend you to use the items provided with your PC100 and follow our instructions for inte- grating the product with your monitor in order to ensure the correct results. Attention The illustrations shown are to guide your integration and may differ from your product.
  • Page 4 As shown below, use screws to secure the Box Guide in the four tap holes at the back of the monitor. Attach the Box Guide to the rail slots, and press it upward. Use screws to secure the product and the Box Guide as shown below.
  • Page 5 Connect the appropriate power cables to a monitor and PC100 respectively. MIC IN MIC IN MIC IN MIC IN Connect the D-sub port of PC100 and RGB-IN port of the monitor with a D-sub cable. MIC IN MIC IN MIC IN MIC IN...
  • Page 6 MIC IN Connect PC100 (OUT) to the monitor (IN) with an RS-232C cable. MIC IN MIC IN MIC IN MIC IN MIC IN Connect the PC100 to the monitor with a LINE-OUT cable. MIC IN MIC IN MIC IN MIC IN Connect a LAN cable to the PC100.
  • Page 7 HDMI cable connections do not require an additional audio in cable. Attention ● The monitor to connect with PC100 should have the HDMI in for the HDMI connection. ● To use the HDMI device, you need to activate the HDMI device in Microsoft Windows Embedded Standard, the operating system of the PC100.
  • Page 8 Connect PC100 (OUT) to the monitor (IN) with an RS-232C cable. MIC IN MIC IN MIC IN MIC IN Connect a LAN cable to PC100. MIC IN MIC IN MIC IN MIC IN...
  • Page 9 Connecting a Monitor with DP Cable Attention ● To enable DP connection, the monitor that will be connected to PC100 must support the DP input port. ● When connecting the DP (DisplayPort) cable, use the standard cable. Using a non-standard cable may cause a malfunction.
  • Page 10 MIC IN Connect PC100 (OUT) to the monitor (IN) with an RS-232C cable. MIC IN MIC IN MIC IN MIC IN MIC IN Connect the PC100 to the monitor with a LINE-OUT cable. MIC IN MIC IN MIC IN MIC IN Connect a LAN cable to PC100.
  • Page 11 Note ● SuperSign software and manual. - Downloading from the LG Electronics website. - Visit the LG Electronics website (http://www.lgecommercial.com/supersign) and download the latest software for your model. (Depending on the model, this feature may not be supported.)
  • Page 12 PC200 Monitor Integration Remove the screw & metal cover. Attach the product to the rail slots, and press it upward. Note If card does not become fully inserted into the insertion direction. Hit by hand carefully to make fully connected. Use screws to secure the product and the product as shown below.
  • Page 13: Optional Items

    Note ● SuperSign software and manual. - Downloading from the LG Electronics website. - Visit the LG Electronics website (http://www.lgecommercial.com/supersign) and download the latest software for your model. (Depending on the model, this feature may not be supported.) Optional Items The following items are supported by the PC700, but are not provided with the product.
  • Page 14 ● Attaching the product with non-standard screws may cause damage or the product to fall down. LG Electronics is not liable for any accidents relating to the use of non-standard screws. ● Do not over tighten the screws as this may cause damage to the product and void your warranty.
  • Page 15 Push the PC700 into the compartment to ard screws may cause damage or the mount it. product to fall down. LG Electronics is not liable for any accidents relating to the use of non-standard screws. ● Do not over tighten the screws as this may cause damage to the product and void your warranty.
  • Page 16 ● Attaching the product with non-standard screws may cause damage or the product to fall down. LG Electronics is not liable for any accidents relating to the use of non-standard screws. ● Do not over tighten the screws as this may cause damage to the product and void your warranty.
  • Page 17 PC700 In/Out Cable Connection Attention ● RGB, DP(Display Port), LINE-OUT(Audio Out), and LAN cables are not included. You need to purchase these separately, if needed. ● After cabling is complete, assign the SET ID of the monitor to be connected to PC700. ●...
  • Page 18 Connect the PC700 to the monitor with a LINE-OUT(Audio Out) cable. AUDIO AUDIO Connect PC700 (OUT) to the monitor (IN) with an RS-232C cable.
  • Page 19 Connect a LAN cable to PC700.
  • Page 20 Connecting a Monitor with DP(Display Port) Cable Connect the appropriate power cables to a monitor and PC700 respectively. Connect PC700 to the monitor via a DP cable. Connect PC700 to the monitor (IN) with an RS-232C cable.
  • Page 21 Connect a LAN cable to PC700. Attention ● If you connect multiple cables simultaneously and turn the product on, video output is prioritized accordingly. ● For DP output, the screen is displayed only when the power is turned on after connecting the cables or when the cables are connected after the OS is booted.

This manual is also suitable for:

Pc200Pc700