Section 6: Supervisor Code Functions - Metro DataVac Flexline FL420 User Manual

- Enter PIN number to coincide with new Service Code or Press OK to
skip.
- Press OK to accept new Service Code / PIN number.
- Enter Service Name or Press OK to skip.
- Press OK to accept Service name.
- Press "SIGN OUT" to exit Set Up Mode.
Setting the Cart ID:
- Press OK to wake up touch pad.
- Enter Set Up Code & Press OK.
- Press "FUNCTION" key several times until "SET THE CART ID" is
displayed & Press OK.
- Current ID will display on screen.
- Press OK to change current ID or "SELECT" to skip.
- Enter new Cart ID (must be 2 to 4 digits) & Press OK.
- Press OK to accept new Cart ID.
- Current Cart Name will display on screen.
- Press OK to change Cart Name or "SELECT" to skip.
- Enter new Cart Name & Press OK.
- Press OK to accept new Cart Name, to change press "CLEAR".
- Press "SIGN OUT" to exit Set Up Mode.
Add New Supervisor Code:
- Press OK to wake up touch pad.
- Enter Set Up Code & Press OK.
- Press "FUNCTION" key several times until "ASSIGN A NEW
MANAGER ID" is displayed & Press OK.
- Enter New 4-digit Supervisor Code & Press OK.
- Enter PIN number to coincide with new Supervisor Code or Press OK
to skip.
- Press OK to accept new Supervisor Code / PIN number or "CLEAR"
to change.
- Enter Supervisor Name or Press OK to skip.
- Press OK to accept Supervisor name.
- Press "SIGN OUT" to exit Set Up Mode.
Delete Existing Supervisor Code:
- Press OK key to wake up touch pad.
- Enter Set Up Code & Press OK.
- Press "FUNCTION" key several times until "DELETE A MANAGER
ID" is displayed & Press OK.
- Enter Supervisor Code to be deleted & Press OK or "CLEAR" to
change.
- Press OK again.
- Press "SIGN OUT" to exit Set Up Mode.
Edit Existing Supervisor Code:
Note: Cannot change Supervisor Code itself but can Edit information
tied to Supervisor Code (i.e., PIN & Name).
- Press OK to wake up touch pad.
- Enter Set Up Code & Press OK.
- Press "FUNCTION" key several times until "EDIT A MANAGER ID" is
displayed & Press OK.
- Enter Supervisor Code to be edited & Press OK.
- Press OK to Add/Change PIN number to coincide with Supervisor
Code or Press "SELECT" to skip.
- Press OK to Add/Change Supervisor Name to coincide with
Supervisor Code or Press "SELECT" to skip.
- Press OK to accept Supervisor name.
- Press "SIGN OUT" to exit Set Up Mode.
FL420 Electronic Locking User Guide - General Operating Instructions

Section 6: Supervisor Code Functions

Edit Existing Supervisor Code:
Note: Cannot change Supervisor Code itself but can Edit information
tied to Supervisor Code (i.e., PIN).
- Press OK to wake up touch pad.
- Enter Supervisor Code & Press OK.
- Press "FUNCTION" key several times until "CHANGE THE
MANAGER PIN" is displayed & Press OK.
- Enter current PIN or Press OK if there is no current PIN.
- Enter New PIN or Press OK to skip.
- Press OK to accept new PIN or press "CLEAR" to change..
- Press "SIGN OUT" to exit Supervisor Mode.
Add New User Code:
- Press OK to wake up touch pad.
- Enter Supervisor Code & Press OK.
- Press "FUNCTION" key several times until "ASSIGN A NEW
OPERATOR ID" is displayed & Press OK.
- Enter New 4-digit User Code & Press OK.
- Enter PIN number to coincide with new User Code then re-enter the
PIN OR press OK to skip.
- Enter User Name or Press OK to skip.
- Press OK to accept User name.
- "THE OPERATOR WAS ASSIGNED" should display on screen.
- Press OK to continue.
- Press "SIGN OUT" to exit Supervisor Mode.
Delete Existing User Code:
Note: Only the 4-digit User Code has to be entered to delete the user;
If User added PIN, it is not necessary for Supervisor to know the PIN to
Delete the User.
- Press OK to wake up touch pad.
- Enter Supervisor Code.
- Press "FUNCTION" key several times until "DELETE AN OPERATOR
ID" is displayed & Press OK.
- Enter 4-digit User Code to be deleted & Press OK.
- Press OK again to delete User Code.
- Press "SIGN OUT" to exit Supervisor Mode.
Edit Existing User Code:
Note: Cannot change User Code itself but can edit information tied to
User Code (i.e., PIN, Name, Card). To change User Code, must
Delete existing code & Add new code.
- Press OK key to wake up touch pad.
- Enter Supervisor Code & Press OK.
- Press "FUNCTION" key several times until "EDIT AN OPERATOR ID"
is displayed & Press OK.
- Enter the User Code to be edited.
- Press OK to change the User PIN or Press "SELECT" to skip.
- Press OK to change the current User Name or Press "SELECT" to
skip.
- The Operator ID was updated will display on screen.
- Press OK to continue.
- Press "SIGN OUT" to exit Supervisor Mode.
Add New User Card:
Note: Only for a cart that is equipped with a card reader; this function
can be performed by the Supervisor or User.
- Press OK to wake up touch pad.
- Enter Supervisor Code & Press OK.
- Press "FUNCTION" key several times until "ASSIGN A NEW
OPERATOR ID" is displayed & Press OK.
- Enter New 4-digit User Code & Press OK.
2
continued...