Full Boar FBCWDV-1225PT Instruction Manual
Full Boar FBCWDV-1225PT Instruction Manual

Full Boar FBCWDV-1225PT Instruction Manual

Wet & dry vacuum 25l cyclonic

Advertisement

KNOW YOUR PRODUCT
WET & DRY
VACUUM
25L CYCLONIC
• 1200W MOTOR
• BAGLESS DUST & LIQUID
COLLECTION
• CYCLONIC ACTION, HIGH
POWER SUCTION
INSTRUCTION MANUAL
WARNING: Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
0719

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FBCWDV-1225PT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Full Boar FBCWDV-1225PT

  • Page 1 KNOW YOUR PRODUCT WET & DRY VACUUM 25L CYCLONIC • 1200W MOTOR • BAGLESS DUST & LIQUID COLLECTION • CYCLONIC ACTION, HIGH POWER SUCTION INSTRUCTION MANUAL WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
  • Page 2: Specifications

    SPECIFICATIONS - MODEL NO. FBCWDV-1225PT Mains Voltage: 220Ð240V ~ 50Hz Input Power: 1200W Power Outlet Max.: 1200W Psum: 2400W Suction Power Max.: 200 mbar Suction Volume: 24 l/s Tank Capacity: 25 l Suction Hose:: ¯35mm x 1.5m IP Rating IPX4...
  • Page 3 KNOW YOUR PRODUCT (cont.) 13. Transparent tank 1. Flexible suction hose 2. Carry handle 14. Vacuum inlet. 3. Appliance head 15. Wheels x 2 4. On/off/automatic switch 16. Quick height adjustment 5. Automatic power take-off outlet 17. Small floor tool 6.
  • Page 4: Table Of Contents

    TABLE OF CONTENTS SPECIFICATIONS............Page 02 KNOW YOUR PRODUCT........... Page 02 INTRODUCTION............Page 05 SAFETY INSTRUCTIONS........... Page 05 ASSEMBLY..............Page 10 SUCTION TOOLS............Page 13 OPERATION............... Page 14 MAINTENANCE............Page 16 DESCRIPTION OF SYMBOLS........Page 18 CONTENTS..............Page 19 WARRANTY..............Page 20...
  • Page 5: Introduction

    The electric motor has been designed for 220V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate. Note: The supply of 230V and 240V on Full Boar tools are interchangeable for Australia and New Zealand.
  • Page 6 GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool.
  • Page 7 GENERAL POWER TOOL SAFETY WARNINGS (cont.) e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.
  • Page 8 WET & DRY VACUUM SAFETY WARNINGS IMPORTANT! When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating manual with due care. Keep this manual in a safe place so that the information is available at all times.
  • Page 9 WET & DRY VACUUM SAFETY WARNINGS (cont.) • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Page 10: Assembly

    ASSEMBLY KNOW YOUR PRODUCT WARNING! During assembly ensure the cyclonic wet and dry vac is switched OFF and disconnected from the power supply. Fitting the wheels (15): Each of the wheels has a different shaped bracket. You will need to identify each before fitting into the underside of the vacuum.
  • Page 11 KNOW YOUR PRODUCT ASSEMBLY (cont.) Fitting the appliance head (3) 1. The appliance head (3) is fastened to the Fig. 4 transparent tank (13) by the appliance securing clips (12 ). 2. To remove the appliance head (3), open the clips (12) and lift the appliance head (3) by the carry handle (2) (fig.
  • Page 12 ASSEMBLY (cont.) Fitting the flexible suction hose (1) 1. Connect the suction hose (1) to the vacuum inlet (14) on the cyclonic wet and dry vacuum (fig. 7) 2. Press the release button (6) to remove suction hose (1) (fig. 8).. Fig.
  • Page 13: Suction Tools

    SUCTION TOOLS Dual purpose floor tool (23) The dual-purpose floor tool is for vacuuming solids, dust on carpet and hard floors over medium and large areas (fig. 11). Fig. 11 Wet floor tool (20) The wet floor tool is for vacuuming liquids over medium to large area (fig.
  • Page 14: Operation

    OPERATION WARNING! The power supply for this product should be protected by a residual current device rated at 30mA or less. ON/OFF/AUTOMATIC switch (4) Switch position 0: Off (fig. 16) Switch position I: Normal operation Switch position: Automatic mode Fig. 16 Water drain outlet (7) To make the transparent tank (13) easier to empty after wet vacuuming, it is fitted with a...
  • Page 15 OPERATION (cont.) Automatic mode (1200W max.) Connect the power cable on your electric tool to the automatic power take off outlet (5) and connect the flexible suction hose (1) to the extractor connector on your electric tool. Check that the connections are secure and airtight.
  • Page 16: Maintenance

    MAINTENANCE WARNING! Before cleaning your cyclonic wet & dry vac or carrying out any maintenance procedure, make sure that the motor is off and the vac disconnected from the power supply to prevent accidental starting. Cleaning Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible.
  • Page 17 MAINTENANCE (cont.) Cleaning the filter cartridge (24) Remove the foam from the underside of the filter cartridge (fig. 22). Clean both parts with a little soft soap under running water and allow them to air-dry. Note: Ensure the filters are completely dry after cleaning as water may drip from the filters and come into contact with the water sensor preventing normal operation.
  • Page 18: Description Of Symbols

    DESCRIPTION OF SYMBOLS Litres Read instruction manual lPX4 mbar Ingress protection from water Pressure rating (millibar) Litres per second CARING FOR THE ENVIRONMENT Power tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way.
  • Page 19: Contents

    CONTENTS 1 x Cyclonic wet & dry vac 2 x Wheels 4 x Screws 2 x Castors 1 x Suction tube, telescopic 1 x Crevice tool 1 x Upholstery tool 1 x Small floor tool 1 x Dual purpose floor tool 1 x Wet floor tool 1 x Foam filter 1 x Filter cartridge...
  • Page 20: Warranty

    WARRANTY YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE (see www.bunnings.com.au or www.bunnings.co.nz for store locations) WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE: Australia 1800 069 486 New Zealand 0508 069 486...

Table of Contents