Full Boar FBWDV-1240PT Instruction Manual

Full Boar FBWDV-1240PT Instruction Manual

40l - l class

Advertisement

KNOW YOUR PRODUCT
WET & DRY
VACUUM
40L - L CLASS
• 40L STAINLESS STEEL
TANK
• 1200W MOTOR
• L - CLASS CERTIFIED
• HEPA FILTER - 99.95%
RETENTION
INSTRUCTION MANUAL
WARNING: Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
0419

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FBWDV-1240PT and is the answer not in the manual?

Questions and answers

Chris Finnie
March 4, 2025

how long is the cord on the Bull boar Wet & Dry vacuun 40L L Class?

Summary of Contents for Full Boar FBWDV-1240PT

  • Page 1 KNOW YOUR PRODUCT WET & DRY VACUUM 40L - L CLASS • 40L STAINLESS STEEL TANK • 1200W MOTOR • L - CLASS CERTIFIED • HEPA FILTER - 99.95% RETENTION INSTRUCTION MANUAL WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
  • Page 2: Specifications

    SPECIFICATIONS - MODEL NO. FBWDV-1240PT Voltage: 220Ð240V ~ 50-60Hz Input power: 1200W Power outlet max.: 1200W Psum: 2400W Suction power max.: 220 mbar Tank capacity (Dry): 40 l (Wet): 28 l Suction hose:: ¯36mm x 3m Dust class: (Can be used for materials where the dust OEL values are >1mg/m3)
  • Page 3 KNOW YOUR PRODUCT (cont.) 1. Main handle 15. Blower port 29. Dust bag (Dry) 2. Filter clean button 16. Filter cover 30. Foam filter (Wet) 3. 2 x Handle fastener 17. Accessory bracket 31. Coarse filter (Dry) 4. On/off/automatic switch 18.
  • Page 4: Table Of Contents

    TABLE OF CONTENTS SPECIFICATIONS............Page 02 KNOW YOUR PRODUCT........... Page 02 INTRODUCTION............Page 05 SAFETY INSTRUCTIONS........... Page 05 ASSEMBLY..............Page 10 SUCTION NOZZLES........... Page 13 OPERATION............... Page 14 MAINTENANCE............Page 16 DESCRIPTION OF SYMBOLS........Page 18 CONTENTS..............Page 19 WARRANTY..............Page 20...
  • Page 5: Introduction

    The electric motor has been designed for 220V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate. Note: The supply of 230V and 240V on Full Boar tools are interchangeable for Australia and New Zealand.
  • Page 6 GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool.
  • Page 7 GENERAL POWER TOOL SAFETY WARNINGS (cont.) d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
  • Page 8 WET & DRY VACUUM SAFETY WARNINGS IMPORTANT! When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating manual with due care. Keep this manual in a safe place so that the information is available at all times.
  • Page 9 WET & DRY VACUUM SAFETY WARNINGS (cont.) • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Page 10: Assembly

    ASSEMBLY KNOW YOUR PRODUCT WARNING! During assembly ensure the wet and dry vac is switched OFF and disconnected from the power supply. Fitting the wheels (13) 1. Place a R-clip (33) for fitting the wheels through the appropriate hole in the axle (36) (Fig.
  • Page 11 KNOW YOUR PRODUCT ASSEMBLY (cont.) Fitting the motor head 1. The motor head is fastened to the tank (8) by the motor securing clips (6) (Fig. 7). 2. To remove the motor head, open the motor securing clips (6) and lift the motor head (Fig.
  • Page 12 ASSEMBLY (cont.) Fitting the coarse filter (31) - vacuuming dry matter: The coarse filter (31) can be used for when vacuuming large amounts of fine dust (with or without a dust bag (29). Note: The coarse filter (31), is not suitable for wet vacuuming.
  • Page 13: Suction Nozzles

    SUCTION NOZZLES Telescopic suction tube (19) The flexible suction hose (37) Fig. 19 can be extended by attaching Fig. 18 the telescopic suction tube (19) (Fig. 18). The height of the telescopic suction tube (19) can be adjusted by using the quick height adjustment.
  • Page 14: Operation

    OPERATION WARNING! The power supply for this product should be protected by a residual current device rated at 30mA or less. ON/OFF/AUTOMATIC switch (4) (Fig. 25) Switch position 0: Off Switch position I: Normal operation Switch position AUTO: Automatic mode - for use in power take-off function.
  • Page 15 OPERATION (cont.) Water drain outlet (9) To make the Tank (8) easier to empty after wet vacuuming, it is fitted with a water drain outlet (9). Open the water drain outlet (9) by turning it anti-clockwise (Fig. 31) and drain the liquid. Fig.
  • Page 16: Maintenance

    OPERATION (cont.) Drilling nozzle (20) Due to the smooth flat surface of the drilling nozzle the suction of the vacuum cleaner will fix the drilling nozzle to the drilling surface, you can drill holes with both hands on the drill and have a cleaner work environment.
  • Page 17 MAINTENANCE (cont.) Cleaning the filters Cleaning the HEPA filter (28) The HEPA filter should be checked at regular intervals and cleaned if necessary. If used on a daily basis, change once a year or if damaged. 1. Wear an appropriate air filter face mask. 2.
  • Page 18: Description Of Symbols

    DESCRIPTION OF SYMBOLS Litres Read instruction manual lPX4 mbar Ingress protection from water Pressure rating (millibar) Dust class Max. transmittance Hazards / suitable for Keeps back 99% of: • Dust with OEL values > 1 mg/m³ • Slightly hazardous dusts CARING FOR THE ENVIRONMENT Power tools that are no longer usable should not be disposed of with household waste but in an environmentally...
  • Page 19: Contents

    CONTENTS 1 x Wet & Dry Vac 1 x Main handle 1 x Air regulator 2 x Wheels 2 x Castors 2 x Wheel covers 2 x Securing split pins for wheels 4 x Washers for fitting the wheels 2 x Bolts for fitting main handle 1 x Axle 1 x Suction tube, telescopic 1 x Electric tool adaptor...
  • Page 20: Warranty

    WARRANTY YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE (see www.bunnings.com.au or www.bunnings.co.nz for store locations) WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE: Australia 1800 069 486 New Zealand 0508 069 486...

Table of Contents