Page 1
Model: Y0LSX46B000 18" Cordless Chain saw OPERATOR’S MANUAL Our Customer Service staff is ready to provide assistance. In the case of a damaged or missing part, most replacement parts ship directly from Merotec USA in Atlanta or from one of our service partners in the US.
TABLE OF CONTENTS Description of product parts........................Technical specification........................... Intended use............................General safety warnings......................... Product safety warnings......................... Symbols..............................Installation............................... Operation..............................Maintenance and storage........................Troubleshooting............................Warranty............................. WARNING To reduce the risk of electric shock- Do not expose to water. Do not use in rain. Store indoors only. Replace damaged battery pack immediately. Disconnect battery pack before cleaning or servicing.
Work area safety Keep work area clean and well lit. Cluttered Technical Specifications or dark areas invite accidents. Model # Y0LSX46B000 Do not operate power tools in explosive Voltage/Capacity 120 V DC, 2.5 Ah Li-ion atmospheres, such as in the presence of No-load chain speed 42.65 ft/s (13 m/s)
Page 7
120v LITHIUM-ION on the switch or energizing power tools that Electrical safety have the switch on invites accidents. Power tool plugs must match the outlet. Remove any adjusting key or wrench Never modify the plug in any way. Do before turning the power tool on. A not use any adapter plugs with earthed wrench or a key left attached to a rotating (grounded) power tools.
Page 8
Keep cutting tools sharp and clean. charge out with the prescribed temperature Properly maintained cutting tools with sharp range may automatically be blocked by cutting edges are less likely to bind and are the protection circuitry of the battery pack. easier to control.
120v LITHIUM-ION condition. Hold the power tool by insulated gripping Always allow the product to cool down before surfaces only, because the saw chain storing. may contact hidden wiring. Saw chains When servicing the chain be aware that even contacting a "live" wire may make exposed though he power source is switched off, the metal parts of the power tool "live"...
Page 10
than intended could result in a hazardous 14. Cut the wood in right direction. situation. 15. Before use the chain saw, be sure to 13. Causes and operator prevention of check the chain and bar in tension. Don’t kickback: use the chain saw if the chain and bar are loose.
120v LITHIUM-ION Symbols Wear ear hearing protection when operating this product. Safety symbols The purpose of safety symbols is to attract your Wear eye protection attention to any possible dangers. The safety symbols and their explanations deserve your careful attention and full understanding. The Wear heavy-duty protective gloves when symbol warnings do not, by themselves, eliminate handling the chain saw.
Adjust the chain’s tension Do not expose and operate the tool in rain. Use a flat screwdriver to adjust the tension of chain, clockwise direction to tighten, and anticlockwise direction to release. Warning symbols on the charger 0.079“ The charger is for indoor use only. Double insulation Protective 6.3A limited CAUTION! Always ensure the battery pack has...
120v LITHIUM-ION Operation 4. When there is fault with the battery pack, the red LED light will flash. 5. Once the battery pack is correctly located in Charging the battery pack the charger, the 4 green LED lights of the battery pack will flash LED lights to indicate the NOTE: charging process.
Page 14
To insert the battery pack 3. Grip the main handle with your right hand and 1. Align the groove on the battery pack with the auxiliary handle with left hand. corresponding ribs in the receptacle of the device. (See Fig. 7) 4.
Page 15
120v LITHIUM-ION General using method Notching undercut 1.Use the chain saw only with secure footing. Make the notch 1/3 the diameter of the tree, 2.Always hold the chain saw firmly with both perpendicular to the direction of falls. hands. Front grip with the left hand and rear grip with the right hand.
Bucking a log Bucking is cutting a log into lengths. It is important to make sure your footing is firm and your weight is evenly distributed on both feet. When possible, the log should be raised and supported by the use of limbs, logs or chocks. Follow the simple directions for easy cutting.
Page 17
120v LITHIUM-ION Cutting System Maintenance: 1. Check that the lubrication system is adequate. 2. Turn the bar over every day. 3. Check the bar wear. 4. Ensure that the oil flow hole is unobstructed. 5. Check the chain tension, sharpen the blades and check their conditions eventually removing irregularities.
Troubleshooting WARNING ! Before performing any repair work, always ensure that the battery pack/safety key has been removed and wait until the tool has stopped completely. WARNING ! Always wear heavy duty gloves when adjusting or cleaning. Fault/malfunction Cause Remedy Chainsaw does not power ON Battery discharged? Recharge the battery.
Yard Force. 3. If service or a warranty evaluation is requested, Yard Force will provide an RGA number that should be used in all communications with Yard Force and is required to be indicated on the product itself and on the outside of the box.
Page 20
1-866-902-9690 support@merotecusa.com Need Help? Please do not return the product to the place of purchase yet. We’re here to help and take care of all your needs. Contact our Customer Care Center in Atlanta, GA for help with: Product assembly or use Missing or damaged parts Troubleshooting You can also visit our website to download...
Need help?
Do you have a question about the Y0LSX46B000 and is the answer not in the manual?
Questions and answers