Before The First Use; Making Juice - Maxwell MW-1105 ST Manual Instruction

ENGLISH
The unit is intended for household use only,
its commercial usage is prohibited.

BEFORE THE FIRST USE

After unit transportation or storage at low
temperature it is necessary to keep it for at
least two hours at room temperature before
switching on.
– Unpack the juice extractor.
Disassemble and clean the juice extractor
before usage:
• Remove the pusher (1) from feeding chute
(2) on the juice extractor lid (3).
•
Lower the locking arm (7) and release the
lid (3).
•
Remove the lid (3).
• It will be easier to remove the grating filter (4)
if you remove it with the juice collector (5),
holding the juice collector (5) and pulling it
upwards.
•
Wash thoroughly and dry all the removable
parts that will contact food.
Note:
Be cautious when holding grating filter
–
(4) in your hands, as disc grating surface
is very sharp.

MAKING JUICE

Before the first use make sure that the operat-
ing voltage of the unit corresponds to voltage of
your mains.
Fruit and vegetables should be fresh.
Before juice extracting wash fruit/vegetables
and cut them into pieces easily fitting into the
feeding chute (2), having removed inedible parts
from vegetables or fruit, such as stems, hard
peel or stones, for example, cherry or peach.
Place the motor unit (8) on a dry, flat and
–
steady surface.
Before assembling the juice extractor make
–
sure that the operation modes switch is set to
the position «0», and the plug is not inserted
into the socket.
Attach the juice collector (5) to the motor
–
unit (8).
Install the grating filter (4) inside the juice
–
collector (5).
Attention!
Do not use juice extractor if you found me-
chanical damages of grating filter (4).
mw-1105.indd 8
Install the lid (3) on the juice collector (5) and
–
fix it by placing the locking arm (7) in verti-
cal position.
Install pulp container (10) to its place.
–
Set the cup (11) under the juice draining
–
spout (6).
Lower the juice draining spout (6) by press-
–
ing it (fig. 1).
Insert the power plug into the socket.
–
Switch the juice extractor on by setting the
–
switch (9) to the position «I» (low speed) or
to position «II» (high speed).
Note:
Low speed «I» is intended for extracting of juice
from soft vegetables/fruits – such as tomatoes,
ripe pears, strawberry, oranges, plums, grapes,
pumpkin, onion, cucumbers and etc.
High speed «II» is intended for extracting of
juice from hard vegetables/fruits – such as arti-
choke, carrots, apples, paprika, beet, potatoes,
pineapples, vegetable marrows, celery, spin-
ach, dill, leek etc.
Attention! To avoid the grating filter (4) stop-
ping and motor rotor jamming during the
processing of viscous or quite hard food it is
recommended to use the high speed opera-
tion mode «II» of the juice extractor.
The unit will be switched on only if all the
–
removable parts are installed properly, and
the lid (3) is fixed with the locking arm (7).
Feed the food into the feeding chute (2)
–
located on the lid (3) only when grating filter
(4) is rotating.
Put the preliminary cut vegetables or fruits
–
gradually into the feeding chute (2) located
on the lid (3) and push them slightly with the
pusher (1). Do not press on the pusher (1)
too hard as it can lead to decrease of juice
amount and even to grating filter (4) rotation
stopping. The slower is the fruit and veg-
etables processing, the higher is the juice
extraction rate.
Do not put your fingers or any other objects
–
into the feeding chute (2) located on the lid
(3).
During the operation check the grating filter
–
(4) periodically for obstruction of mesh with
pulp, if necessary wash the grating filter (4);
before removing the grating filter switch the
juice extractor off and unplug it.
8
11.03.2013 10:40:48