Table of Contents
Advertisement
Quick Links
Aquavar SOLO
2
FREQUENTLY ASKED QUESTIONS / AQSOLO2FAQ
How do I size the Aquavar SOLO² for the appropriate pump/motor combination?
Can I run the Aquavar SOLO² up to 80 HZ?
What are the recommended spare parts for an Aquavar SOLO²? Can I repair?
Can I mount the Aquavar SOLO² controller in an outside environment? If so what are the maximum conditions
allowed?
What if my Aquavar SOLO² controller is not putting out the recommended output in GPM?
Is the unit sensitive to lighting strikes or voltage disturbances?
Can I use the Aquavar SOLO² with generators?
Can I use GFCI protected power for the Aquavar SOLO² controller?
Is my pressure transducer sensitive to stray voltage and electrical disturbances?
Will the Aquavar SOLO² increase the life of my pump and motor compared to a conventional switch system?
Is the pressure transducer operation sensitive to poor signal and electrical disturbances?
Can submersible cable (copper 75°) be used to extend the length of transducer?
When sizing the Aquavar SOLO² for use with another motor manufacturer, is it recommended to upsize to the next size
Aquavar SOLO², to maximize the performance of the pump?
Can the Aquavar SOLO² run without the pressure transducer/or if there is a transducer failure?
What accessories are offered for use with the Aquavar SOLO²?
Can I use a float switch instead of a pressure transducer with the Aquavar SOLO²?
How far can the float switch be from the drive? What is the maximum total length for pressure transducer cable?
Is the pressure transducer affected by a vacuum, or by water hammer?
What causes a pressure fluctuation of more than 5 PSI (assuming the controller is set at 5 PSI not 20)?
What is the proper orientation and location for the pressure transducer?
How can the Aquavar SOLO² be used to develop a well system?
Can the Aquavar SOLO² be used for surface mount booster applications? What are the motor electrical requirements?
Can I run a 50 Hz motor with the Aquavar SOLO² or use the Aquavar SOLO² in a 50 Hz application?
Can I use a 208V input on the Aquavar SOLO²?
Can the Aquavar SOLO² run a chlorinator or another external metering pump?
Advertisement
Table of Contents
Related Manuals for Xylem CentriPro Aquavar SOLO 2
Summary of Contents for Xylem CentriPro Aquavar SOLO 2
- Page 1 Aquavar SOLO FREQUENTLY ASKED QUESTIONS / AQSOLO2FAQ How do I size the Aquavar SOLO² for the appropriate pump/motor combination? Can I use a 208V motor? Can I run the Aquavar SOLO² up to 80 HZ? What are the recommended spare parts for an Aquavar SOLO²? Can I repair? Can I mount the Aquavar SOLO²...
- Page 2 CentriPro Residential Water HOW DO I SIZE THE AQUAVAR SOLO² FOR THE APPROPRIATE PUMP/MOTOR COMBINATION? The Aquavar SOLO² can accept any 3 phase, 230 volt 4” submersible motor up to its rated amperage. The Aquavar SOLO² has an adjustable overload switch to dial in the correct full load or service factor amperage. CAN I USE A 208V MOTOR? Yes, The Aquavar SOLO²...
- Page 3 CentriPro Residential Water IS THE UNIT SENSITIVE TO LIGHTING STRIKES OR VOLTAGE DISTURBANCES? Yes. Nothing can prevent direct hits from lightning, however, the Aquavar SOLO2 does use surge arrestors to prevent damage of indirect strikes and intermittent voltage fluctuations. These protective devices are the same as used in expensive residential surge arrestors for computers and electronic protection.
- Page 4 CentriPro Residential Water WHEN SIZING THE AQUAVAR SOLO² FOR USE WITH ANOTHER MOTOR MANUFACTURER, IS IT RECOMMENDED TO UPSIZE TO THE NEXT SIZE AQUAVAR SOLO², TO MAXIMIZE THE PERFORMANCE OF THE PUMP? The Aquavar SOLO² is rated for use with most submersible motors for their given horsepower rating. Please compare the service factor amps (SFA) on the motor to the maximum output on the drive.
- Page 5 Yes, however the external pump requires its own power source. The Aquavar SOLO² can provide an output signal to control the metering pump. Please reference IM229 for additional set up. Back to Frequently Asked Questions Xylem Inc. CentriPro is a trademark of Xylem Inc. or one of its subsidiaries. PAGE 5 www.xylem.com/centripro © 2020 Xylem Inc.
Need help?
Do you have a question about the CentriPro Aquavar SOLO 2 and is the answer not in the manual?
Questions and answers
i got an F01 error code. i turn the power off for a few minutes and then turn it on. it comes on for a few seconds and shuts off again