Table of Contents
Advertisement
Quick Links
ELECTRONIC PARKING SYSTEM FBSN-8TRF
WITH TIRE PRESSURE MONITORING (TPM) OPTION
SET CONTENTS:
1
2
Green
Black
4x
1x
13
8x
21
1x
R
Black-blue +12/24V
Brown GND
1x
7
16
2x
OPTIONAL SET OF TS3 SENSORS:
(TIRE PRESSURE SENSORS)
CONNECTION INSIDE THE CAR
Green
1
Green
1
5
1
Green
4
1
Green
3
11
Blue
2x
2x
9
1x
8x
15
2x
19
1x
1x
1x
22
1x
8
14
1x
20
21
6
+12 / 24V
-
+
12
8x
4x
25
9x
4x
20
1x
1x
1x
20x
1x
5
4x
X
26
4x
6
1x
10
24
1x
18
2x
Black-yellow: velocity
km/h
Brown:
GND
Black-blue:
+12 / 24V
17
4x
4x
4
1x
Black-yellow:
optional velocity
Black-blue:
+
-
OR
+12V
+24V ONLY
Brown GND
4x
3
2
8
2
3
7
R
4x
Blue
Black
Black
Blue
Advertisement
Table of Contents
Related Manuals for APRI FBSN-8TRF
Summary of Contents for APRI FBSN-8TRF
- Page 1 ELECTRONIC PARKING SYSTEM FBSN-8TRF WITH TIRE PRESSURE MONITORING (TPM) OPTION SET CONTENTS: Green Black Blue Black-yellow: velocity km/h Brown: Black-blue: +12 / 24V Black-blue +12/24V Brown GND Black-yellow: optional velocity Black-blue: +12V +24V ONLY Brown GND OPTIONAL SET OF TS3 SENSORS:...
-
Page 2: Sensors Installation
SENSORS INSTALLATION H = 500 mm H = 650 mm H = 400 - 500 mm 0° -10° 0° H = 350 mm 12 25 +10° +10° Front Rear 9 25 +18° C Blue Black Black Blue REAR Green Green Green Green FRONT... - Page 3 TS3 SENSOR INSTALLATION (OPTION) 2. Stick the tire valve in, put washer and 1. Demount tire valve top, nut and nut on. Use small stick to avoid valve washer. spinning and tighten the nut. Attach sensor to tire valve using 4.
-
Page 4: Installation Of Display Unit
INSTALLATION OF DISPLAY UNIT RIGHT position Black-blue: +12 ... +30V Brown: Black-yellow: velocity km/h Alternative attach: DASHBOARD DASHBOARD... - Page 5 INSTALLATION OF ELECTRONIC CONTROL UNITS 2 BY SCREW 1 BY FASTENING BELT 2x O5.4 ZONES OF DETECTION (FACTORY SETTINGS) ZONE Distance (cm) FRONT CORNER STOP-F STOP-R REAR 50 central / 60 corner FRONT CORNER Pressure warning STOP-F symbol STOP-R CORNER REAR...
- Page 6 Electronic parking system FBSN-8TRF System consists of following parts • Display unit (6) with LCD display, containing microcontroller driving the system and wireless communication interface. • 4 front sensors (1) (marked with green color) are installed in the front bumper.
-
Page 7: Functional Description
Functional description Parking assistant After switching the ignition ON, front sensors are activated. Detection of obstacles and their signaling is launched immediately. After shifting into reverse gear you can hear control signal. Now, both front and rear sensors are activated. Obstacles are signaled audibly by speaker inside the display unit and visually on LCD display. - Page 8 Optional Tire Pressure Monitoring If optional TPM sensors are installed inside the tires, system monitors pressure and temperature in the tires during vehicle drive. In case of any tire problem, warning or alarm is given through the display unit. Moreover display shows pressure inside the tire with largest difference from required pressure. Pressure is displayed any time when there is no need to display parking situation.
-
Page 9: Assembly Guide
Assembly guide Before assembly, study carefully whole the Assembly guide. Switch the ignition OFF. Layout of individual parts of the system is obvious from the picture CONNECTION INSIDE THE CAR. 1. Installation of sensors • Conditions for layout of sensors in bumpers are in the picture. Choose suitable type of brackets and mark centers of the holes. - Page 10 3. Registration of front and rear ECUs – so called learning procedure • Units use wireless communication to transfer data between them. To ensure communication only with its own ECUs installed in bumpers, Display unit has to learn their unique identification numbers (ID). •...
- Page 11 5. Registration of optional TPM sensors • Due to wireless communication with the tire sensors, display unit has to learn their identification numbers. • To do so switch the ignition ON and press and hold for four seconds both pushbuttons of the display unit. Pressure warning symbol together with “LE”...
-
Page 12: Parameters Adjustment
Parameters adjustment Parameters setup is stored inside the Display unit (Master). All parameter values can be displayed on the Display unit or changed using its pushbuttons. WARNING! Unprofessional manipulation with parameters can seriously limit utility of device! To activate Parameters adjustment state press and hold any pushbutton until “SET” appears on the display. Display shows parameter number and letter “F“... -
Page 13: Parameters Review
Parameters review NUMBER DESCRIPTION RANGE FACT. SET. NOTE volume of the speaker 0, 1, 2 0=off, 1=low, 2=high range of front central sensors 50 - 95 [cm] range of rear central sensors 120 - 180 [cm] display shows 20 - 80 range of corner sensors 50 - 95 [cm] front STOP zone width... -
Page 14: Problems Solving
Problems solving • If any sensor is faulty, segment in its position is blinking. Change faulty sensor as soon as possible, system is not fully functional. • If irregular false obstacle indication occurs, it can be one of the following problems: Frost on sensors Clean sensors Sensors are placed too low... -
Page 15: Technical Specifications
Technical specifications Sensors and ECUs driving sensors Display unit --------------------------------------------------------------------------------------------------------------------------------------- Supply voltage 9 - 30 V 9 - 30 V Current consumption when ignition is ON 100 mA max. 100 mA max. Current consumption when ignition is OFF and Front ECU connected to car battery 5 –...
Need help?
Do you have a question about the FBSN-8TRF and is the answer not in the manual?
Questions and answers