Advertisement
Operation Instructions
This hard disk unit is made by the Digital Electronics Corporation for use
with its Panel Computer PL-X900 Series devices. This 2.5 inch 6.0G byte
hard disk is designed to be installed inside a Panel Computer.
(All product names that appear in this manual are the trademarks of their
respective companies.)
Warning - Safety Precautions
• Be sure not to jar or bump this unit when installing it in the Panel Com-
puter. Also, be sure to check that the Panel Computer's power is discon-
nected before installing the hard disk in order to prevent electrical shock.
• Do not attempt to modify or open this unit, due to the danger of shock or
fire.
• When installing this hard disk, be sure to read the following "3 Installa-
tion" section's information completely to insure that the unit is correctly
installed.
To Prevent Accidents
• Since the PL-HD210 is a precision instrument, be sure it is neither hit by
nor pressed strongly against another object. After unpacking, be sure
the unit is not dropped or jolted during installation. Also, a PL built in to
a larger unit (i.e. operation panel) should be removed and packed sepa-
rately prior to shipping.
• Be sure water, liquids or metal particles are not allowed to enter the unit.
Any of these may cause either a breakdown or an electrical shock.
• Do not place or store this unit in a location where there is direct sunlight,
excessive heat, dust or vibration.
• Do not store or operate this unit near chemicals, or where there are chemi-
cal fumes.
• Do not allow anyone other than Digital's own service staff to perform
maintenance or adjustments to this unit.
• Do not move or shift the PL while the PL-HD210 is installed and the
power is ON.
PL-HD210
WARNING
‑1‑
Advertisement
Table of Contents
Related Manuals for Digital Electronics Corporation PL-HD210
Summary of Contents for Digital Electronics Corporation PL-HD210
- Page 1 To Prevent Accidents • Since the PL-HD210 is a precision instrument, be sure it is neither hit by nor pressed strongly against another object. After unpacking, be sure the unit is not dropped or jolted during installation. Also, a PL built in to a larger unit (i.e.
- Page 2 • Do not use the PL-HD210 in locations where corrosive gasses are present, since they can lead to a hard disk breakdown. • To prevent damage to file data, be sure to shut down the unit's OS before turning OFF the main power.
- Page 3 Lifetime ing hours, whichever comes first • The PL-HD210 has a finite usage lifetime. Therefore, be sure to back up all HDD data regularly or prepare a backup HDD unit. • The HDD unit’s lifetime depends on the type of usage and surrounding environment, which may either lengthen or shorten the figure given here.
- Page 4 Hard Disk Unit Settings The PL-HD210 is factory set for use as the PL's Slave drive, however, if the user desires to change this setting so that the PL-HD210 can be used as the PL's Master drive, follow the procedures given below.
- Page 5 Installation Use the following steps to install the PL-HD210 in the PL. WARNING Shock Danger! Be sure to unplug the PL unit prior WARNING : to installing the PL-HD210. Since the PL-HD210 is a precision instrument, be sure it is ! ! ! ! ! neither hit by nor pressed strongly against another object.
- Page 6 Hardware Setup ! ! ! ! ! Normally, the factory settings (default settings) shoul be used. Important All the following explanation screens use the PL's factory settings (default Note: settings). Connect a keyboard to the PL unit. Turn the PL unit’s power ON. When the “Press <DEL>...
- Page 7 OS (MS-DOS or Windows) to create partitions and initialize the hard disk. Please consult your OS’s operation manuals for details. Digital Electronics Corporation 8-2-52 Nankohigashi, Suminoeku, Osaka, 559-0031 Japan Tel. +81 - 6 - 6613 - 1101 (General No.) FAX +81 - 6 - 6613 - 5888 ‑7‑...
Need help?
Do you have a question about the PL-HD210 and is the answer not in the manual?
Questions and answers