Connecting to the Switcher using USB Type C (USB-C) ������������������������������ 12 Quick-Charging Power ���������������������������������������������������������������������������������� 12 Volume Control ���������������������������������������������������������������������������������������������� 13 Volume Control using IR Remote Controller ������������������������������������������������� 13 Volume Control using Switcher Settings Application ������������������������������������� 13 SP-SW5200-VUHBT Users Guide Page 3...
Page 4
Volume Level �������������������������������������������������������������������������������������������������� 16 Mute Audio ����������������������������������������������������������������������������������������������������� 17 Display Control ���������������������������������������������������������������������������������������������� 17 Non-Use Timeout ������������������������������������������������������������������������������������������� 17 Proximity Control ������������������������������������������������������������������������������������������� 17 LAN Settings �������������������������������������������������������������������������������������������������� 18 Debug Mode ��������������������������������������������������������������������������������������������������� 18 Reset ��������������������������������������������������������������������������������������������������������������� 18 Restore System to Factory Defaults ������������������������������������������������������������ 19 Page 4 SP Controls, Inc.
Page 5
[ This page is intentionally blank. ] SP-SW5200-VUHBT Users Guide Page 5...
Users can manually select the device by touching the Input Select button. External control systems, like those manufactured by SP Controls can utilize (a) the RS232 port, (b) the Ethernet port, (c) the IR port, and/or (d) the USB 2.0 (USB-CDC) port.
Ethernet port, USB, and/or Proximity Sensor port.. Power. Connect the DC power supply to the location, “24VDC”, and the other end to your 110V/VAC power socket. The system LED will illuminate above “24VDC” location. SP-SW5200-VUHBT Users Guide Page 7...
The SW5200 has a “pass through” mode that passes all display information requests directly to the display. If this feature is enabled and the system is configured with extenders on the input and output ports of the SW5200 it is possible to have time-outs on certain input devices. Page 8 SP Controls, Inc.
The communication parameters are as follows: 115200 baud, 8 bit, no parity, and 1 stop bit. The baud rate is adjustable. Pins 2 (Rx), 3 (Tx), and 5 (GND) are used. In some instances, the SW5200 may have 24VDC power Pin 9. SP-SW5200-VUHBT Users Guide Page 9...
Settings section. Here are some settings that can be viewed or changed: • EDID table and resolutions • Ethernet setings • Volume adjustments • Auto-switching On/Off • Display inactivity shutdown timeout • Proximity sensor On/Off Page 10 SP Controls, Inc.
From the IR Remote controller, shown below, select the Right or Left buttons until the desired Source is selected. If the front panel is viewable, you will see the Active Source Indicator change when each button is pressed. SP-SW5200-VUHBT Users Guide Page 11...
Volume Control using Switcher Settings Application Volume Control using Switcher Settings Application See next section, Advanced Features, for details on how use the program “Switchers Settings” to adjust real time settings of the SW5200. SP-SW5200-VUHBT Users Guide Page 13...
This screen view uses standard Windows-style menuing to modify the behavior (settings) of thepresentation switcher. In this case, a PS120 is showing. When connected to a SW5200, that device designation will be visible. Real Time Status Section Switcher Settings Communications Status Page 14 SP Controls, Inc.
In this mode, the system looks very similar to those old Terminals. This interface is a menu driven system used to modify switcher features. The HELP menu is shown in the Terminal mode image below. SP-SW5200-VUHBT Users Guide Page 15...
This feature only effects the audio level on the RCA pre-amp outputs. To adjust the audio level, press on the Blue Dot associated with the Volume as show below. Click and drag to the desired level. The lev- el is indicated next to the mouse as the volume is adjusted. Page 16 SP Controls, Inc.
If there is nobody in the presentation space and the display is still turned on, the switch- er will wait 2-10 minutes before shutting the display off. The number of minutes is set using a rotary dial on the proximity sensor itself. SP-SW5200-VUHBT Users Guide Page 17...
When a reset occurs, the SW5200 uses the last-stored settings of the switcher. This means that the switcher will try to restore inputs, resolution, and audio settings to the way they were prior to the reset. Page 18 SP Controls, Inc.
The “Factory Def” or factory defaults button restores all factory detault settings that were used when the SW5200 was first sent to the customer then performs a software reset. However, this function does not reset the LAN Settings. SP-SW5200-VUHBT Users Guide Page 19...
Page 20
Therefore, you must treat the software like any other copyrighted material (e.g., a book or sound recording). Every effort has been made to ensure that the information in this manual is accurate. SP Controls, Inc. & Presentation Switchers, Inc. are not responsible for printing or clerical errors.
Need help?
Do you have a question about the SP-SW5200-VUHBT and is the answer not in the manual?
Questions and answers