Operation - babymoov YOO Care Instructions For Use Manual

In this step, you connect the receiver to the transmitter
to allow them to communicate without other devices
(including Babyphones of the same model) interfering
with you or receiving your signal.
The transmitter and receiver are already paired using a
code pre-set at the factory. However, you should reset
the connection if the event of interference:
1. Press the receiver's On/Off button (20) for two
seconds to turn it on. While the menu icon (14) is
lit (if it does not turn on, press on the On/Off button
(20) briefly), touch the menu to display the main menu
on the screen (16). Press the Up/Down keys (12),
(13) to select the «matching» function, hold down the
On/Off button (20) to confirm.
2. The screen (16) will display the «Unit select» menu:
3. Press the Up/Down keys (12) (13) to select «Baby»,
then hold down the On/Off button (20) to confirm.
Press the Up/Down keys (12) (13) to choose a
number for your transmitter, then hold down the On/
Off button (20) to confirm.
1. Place the transmitter about 1 metre from baby's
bed, pointing the camera (3) and the microphone
(5) towards baby.
2. Turn on the transmitter by holding down the On/
Off button (1) for 2 seconds until the operation/low
battery icon (2) turns green. Release the On/Off
button (1). If the batteries are low, the icon (2) will
turn red. Change the batteries or used the 5V mains
adaptor provided.
3. Now, turn on the receiver by holding down the On/
Off button (20) for 2 seconds until the operation/
low battery icon (10) turns green. If the icon starts
flashing, the battery is low and needs to be recharged
using the 5V mains adaptor.
4. The image filmed by the camera (3) should appear
on the screen (16), while the audio captured by the
microphone (5) should be audible on the speaker
CONNECTING THE TRANSMITTER TO THE RECEIVER
YOO CARE • Instructions for use
4. Press the Up/Down keys (12) (13) to select
«Connect», then hold down the On/Off button (20)
to confirm. The connection icon (11) will flash rapidly
for 15 seconds.
5. Press the On/Off button (1) on the transmitter until
the Operation/Low battery icon (2) begins flashing
green. Release the On/Off button.
6. If connection has worked properly, the screen (16)
will display the image filmed by the camera (3) and
the letter next to «Connection» in the menu will switch
from N to Y. The green light on the connection icon
(11) and the operation/low battery icon (2) remains
on.
N.B.: You must perform step 5 while the connection
icon (11) is flashing quickly for the connection to
be made.
7. The device is ready to use.
8. If connection fails (the image on the screen (16)
doesn't move and doesn't follow the image filmed
by the camera (3), repeat steps 1 to 5.
9. To disconnect a transmitter, follow steps 1 and 2
above. At step 3, select the number of the transmitter
to be disconnected and continue to step 4. Do
not perform step 5, wait for the green light on the
connection icon (11) to stop flashing. Hold down
the On/Off button (20) to turn off the receiver. The
selected transmitter is disconnected.

OPERATION

(17). If the screen displays the message «No signal or
out of range», the devices have not been connected
properly (see the CONNECTION section).
Adjust the speaker (17) volume for comfortable
listening using the Up/Down keys (12) (13). Volume
bars will appear on the screen.
If you don't want to hear, press «Mute» on the
speaker (15). The speaker will be muted and the
«mute» icon will appear on the screen (16). To turn
on the sound again, press on the icon (15) again. The
volume will be restored to its initial level.
N.B.: The keys will work only when the icons
( )are displayed. To activate them, hold
down the On/Off button (20). To avoid mistakes,
the icons will disappear after 8 seconds if no key
is used.
11