3M Speedglas 9100 Manual

3
Speedglas 9100 – Welding Helmet and Hardhat Adapter for
™
use with 3M XLR8 Hardhat, and Other Alternate Hardhat
™
Configurations
** Refer to 3M™ Speedglas™ 9100 Welding Helmet, 3M™ XLR8 Hardhat, or Listed Alternate Hardhat
Complete User's Instructions for List of Product Warnings and Proper Use
Ensemble masque pour soudeurs et adaptateur de casque
dur 9100 Speedglas à utiliser avec le casque dur XLR8 3M
™
et d'autres configurations de casque dur
** Consulter les directives d'utilisation complètes du masque pour soudeurs 9100 Speedglas™, du
casque dur XLR8 3M™ et des autres casques durs indiqués pour connaître les mises en garde et les
directives d'utilisation adéquates du produit.
Speedglas 9100 – Careta para soldadura y Adaptador de
™
casco para uso con Casco 3M
alternativas de Casco
**Remítase a las Instrucciones de Careta para soldadura 3M™ Speedglas™ 9100, Casco 3M™ XLR8
o Casco alternativo listado para consultar la lista de advertencias y uso adecuado del producto.
3M Occupational Health and
Environmental Safety Division
3M Center, Building 0235-02-W-70
St. Paul, MN 55144-1000
Printed in U.S.A.
3M and Speedglas are trademarks of the 3M Company.
Fibre-Metal is a registered trademark of Honeywell.
V-Gard® and Thermalgard® are registered trademarks of Mine Safety Appliances Co. – MSA.
Jackson Safety is a registered trademark of Kimberly Clark.
© 2010 3M Company. All rights reserved.
3M Occupational Health
and Environmental Safety Division
3M Canada Company
P.O. Box 5757 London, Ontario N6A 4T1
Printed in U.S.A.
3M and Speedglas are trademarks of the 3M Company, used under license in Canada
Fibre-Metal is a registered trademark of Honeywell.
V-Gard® and Thermalgard® are registered trademarks of Mine Safety Appliances Co. – MSA.
Jackson Safety is a registered trademark of Kimberly Clark.
© 2010 3M Company. All rights reserved.
Division des produits d'hygiène
industrielle et de sécurité
environnementale de 3M
Compagnie 3M Canada
C.P. 5757
London (Ontario) N6A 4T1
Imprimé au Canada.
3M et Speedglas sont des marques de commerce de 3M, utilisées sous licence au Canada.
Fibre-Metal est une marque déposée de Honeywell.
V-Gard et Thermalgard sont des marques déposées de Mine Safety Appliances Co. – MSA.
Jackson Safety est une marque déposée de Kimberly Clark.
© 3M, 2010. Tous droits réservés.
3M México S.A. de C.V.
Av. Santa Fe No. 190
Col. Santa Fe, Del. Álvaro Obregón
México D.F. 01210
Impreso en EUA.
3M y Speedglas son marcas registradas de 3M Company.
Fibre-Metal es una marca registrada Honeywell.
V-Gard® y Thermalgard® son marcas registradas de Mine Safety Appliances Co. – MSA.
Jackson Safety es una marca registrada de Kimberly Clark.
© 2010 3M Company. Todos los derechos reservados.
XLR8 y otras configuraciones
™
34-8704-7239-5
• This is an addendum to the User Instructions for the 3M™ Speedglas™ 9100 Auto-Darkening Welding
Helmets. Always read and follow the User Instructions provided with each individual component of any
welding helmet or hard hat assembly. User Instructions include important warnings and use limitations.
Failure to do so may result in sickness or death.
• Do not use any welding product without appropriate training. For proper use, see supervisor or User
Instructions or call 3M in U.S.A. 1-800-243-4630. In Canada, call 1-800-267-4414. Failure to do so
may result in sickness or death.
• Always wear ANSI Z87.1-2003 compliant safety spectacles in addition to any welding helmet. Failure
to do so may result in permanent eye injury and vision loss. In Canada, follow CSA Z94.3 and/or the
™
requirements of the authority having jurisdiction in your region.
Introduction
Two ANSI standards cover performance requirements for welding shields combined with hard hats: Z87.1-
2003 Eye and Face Protection Devices and Z89.1-2003 Industrial Head Protection. Both standards require
welding helmets and hard hats to be tested as a complete assembly, as they would be worn by a welder.
Assembling a welding hard hat using components from different manufacturers or brands voids ANSI
compliance unless tests verify that the assemblies remain compliant with the ANSI requirements.
These User Instructions cover the 3M™ Speedglas™ 9100 welding helmet models listed in Table 1, mounted
to certain hard hats that have been independently tested for compliance with the above referenced ANSI
standards. In all cases, the 3M™ Speedglas™ 9100 Hardhat Adapter for 3M™ Speedglas™ 9100 helmets
(part number 06-0014-00NR) was used as the mounting device.
IMPORTANT: To maintain ANSI compliance, use only the exact components listed in these User Instructions.
Specifications
− Eye and Face Impact: ANSI Z87.1-2003 high impact protector (Z87+)
− Head Impact: ANSI Z89.1-2003, Type I (top impact). Refer to hard hat literature for electrical rating.
Table 1. 3M™ Speedglas™ Welding Helmet Options
Speedglas™ Helmet Model Description
06-0100-10 9100, ADF 9100V, Shades 5,8-13
06-0100-10SW 9100 with Sidewindows, ADF 9100V, Shades 5,8-13
06-0100-20 9100, ADF 9100X, Shades 5,8-13
06-0100-20SW 9100 with Sidewindows, ADF 9100X, Shades 5,8-13
06-0100-30 9100, ADF 9100XX, Shades 5,8-13
06-0100-30SW 9100 with Sidewindows, ADF 9100XX, Shades 5,8-13
Hard Hat Options
The configurations that were tested and passed the above referenced ANSI impact test requirements are
summarized in Table 2. Use with hardhats other than those listed in Table 2 have not been tested as complete
assemblies and would void compliance with the above reference ANSI standards. These User Instructions do
not cover 3M™ Speedglas™ ProTop or other 3M™ Speedglas™ systems sold complete with hard hats.
Manufacturer Hard Hat Model
3M XLR8 with 6 Point Ratchet
MSA V-Gard® w/Fas-trac Suspension
MSA Thermalgard® w/Fas-trac Suspension
Fibre-Metal® E2 w/Ratchet Suspension
Bullard® Classic Series w/6pt. Ratchet Suspension
Bullard® S61 w/ Flexgear
Jackson Safety® SC6 w/ Ratchet Suspension 391
Assembly Instructions
1. Follow Figs. 1-7, to properly remove and replace the 3M™ Speedglas™ headgear with the 3M™
Speedglas™ 9100 Hardhat Adapter as shown in Figs. 1 thru 4.
2. Assure to re-configure the head suspension in the hardhat to face the brim backwards as is shown in Fig. 5.
3. Attach the 3M™ Speedglas™ 9100 assembly to the hardhat as shown in Fig. 6 and adjust the Hardhat
Adapter "pin lock" for a tight fit around the hardhat as shown in Fig. 7 for a completed assembly.
FOR MORE INFORMATION
In United States, contact:
Website: www.3M.com/OccSafety
Technical Assistance: 1-800-243-4630
For other 3M products:
1-800-3M-HELPS or 1-651-737-6501
Fig. 1
Fig. 4
WARNING
Table 2. Hard Hat Options
Hard Hat Part No.
45995-00001
475358 thru 475365 & 488146
486959 thru 486963, 487677,
800360, 814343, 10095325
E2 with 3-RW2 suspension
C30R
S61R
3001987 thru 3001996
Fig. 2
1 2
Fig. 6 a-c
Fig. 3
Fig. 5
3
Fig. 7