Advertisement

Quick Links

KAT & PUPPY
PORTALS
A S S E M B LY G U I D E
Save This Guide For Future Reference
PN: 006.0000.30
January 2019

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KAT & PUPPY PORTALS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SHOR-LINE KAT & PUPPY PORTALS

  • Page 1 KAT & PUPPY PORTALS A S S E M B LY G U I D E Save This Guide For Future Reference PN: 006.0000.30 January 2019...
  • Page 2 INTRODUCTION INTRODUCTION Introduction Thank you for purchasing Shor-Line products. As a leader in animal care equipment, our commitment to provide quality products and personable customer service is the same as it was in 1927. This Guide provides information regarding the installation, use, and care of your Shor-Line product.
  • Page 3: Table Of Contents

    General Maintenance & Care ................... 17 Maintenance Recommendations ................17 Care Recommendations .................... 17 SECTION FOUR, TERMS & CONDITIONS Terms And Conditions ................18 Damaged Freight Procedures ..................18 Limited Warranty ..................20 Limitation Of Liability ....................20 Contact Information ...................21 Shor-Line.com...
  • Page 4: General Information

    Refer to the Guide, images and content to assist with the installation of the product. Throughout the Guide, safety notices provide help for a successful installation. SAFETY FIRST! Shor-Line uses the following symbols and signal words to identify potential hazards or unsafe practices: Safety Alert Symbol Indicates a potential personal injury hazard exists.
  • Page 5: Safety Warnings Included In This Guide

    Keep hands clear of possible pinch areas when moving parts, which if not avoided, could result in minor to moderate injury. SHOR-LINE is not responsible for replacing mis-cut or damaged cages. During cleaning and maintenance, DO NOT pull the Portal Door away from the cage wall.
  • Page 6: Section One, Pre-Assembly

    Damage Reporting Follow the instructions within Shor-Line’s Damage and Freight Procedures. Contact Shor- Line (800.444.1579) immediately to expedite the process. After fifteen (15) calendar days of receipt of merchandise, this policy becomes void.
  • Page 7: Parts List

    Standard 2" Gap Cage 902.0000.33 Puppy Portal - Standard Model • Puppy Portal Spacer, 2" Wide (Styles Vary) • 181.9020.10 10.25 wide x 11.5" tall Wide 3" Gap Cage 902.0000.34 Puppy Portal - Wide Model • Spacer Customer Provided Shor-Line.com...
  • Page 8: Tools And Equipment

    (cut) stainless steel edges and cutting tools, and if not avoided, could result in minor or moderate injury. Ensure the tools are properly maintained. Drill bits and cutting heads should be in good order. Use drilling oil as required. Shor-Line.com...
  • Page 9: Section Two, Assembly Procedures

    For the purpose of these instructions each cage will have a unique identifier, the cage on the right is "CAGE ONE" and the cage on the left is considered "CAGE TWO". See FIGURE 2.1 CAGE CAGE FIGURE 2.1 - Cage Identification (Example) Shor-Line.com...
  • Page 10: Cage Door Removal

    SECTION TWO Cage Door Removal Door hinges may vary depending on the release model of the cages. Type III cages are used for this procedure. Contact SHOR-LINE for door removal procedures for older model cages. STEP 1: Ensure both proposed cages are cleared of animals, bedding, and are thoroughly clean.
  • Page 11: Portal Hole

    STEP 8: The Template will have to be rotated to rest in CAGE TWO. Insert the Template and mark the hole location following the same steps used to locate the hole for CAGE ONE. FIGURE 2.5 - Template Shor-Line.com...
  • Page 12: Mark/Punch Starter Hole

    Use the hammer to strike the punch, locating an indention in the panel. This indention provides a starting point for the drill bit. See FIGURE 2.8 and 2.9 FIGURE 2.7 - Punch Location FIGURE 2.8 - Punch Indention FIGURE 2.9 - Punch Indention Shor-Line.com...
  • Page 13: Drill Starter Hole

    Installation of the Portal MUST BE COMPLETED BY A QUALIFIED INSTALLER familiar with sheet metal manipulation/modifications. Cutting or drilling into metal cages can produce sharp or jagged edges which could cause serious lacerations which, if not avoided, could result in SERIOUS INJURY OR DEATH. Shor-Line.com...
  • Page 14 FIGURE 2.16 - Rotate Nibbler Bend, file any edge surfaces protruding from the panel STEP 3: wall that could affect the seal. See FIGURE 2.17 STEP 4: Remove metal shavings and clean the cage of debris. FIGURE 2.17 - Hole Shor-Line.com...
  • Page 15: Portal Installation

    Collapse one end of the Spacer ring inside the other. See FIGURE 2.21 STEP 2: Insert the Spacer ring in-between the two cages. HOLD IN PLACE. See FIGURE 2.22 & 2.23 FIGURE 2.22 - Spacer Insertion FIGURE 2.23 - Spacer Installed Shor-Line.com...
  • Page 16: Flange Components Installation

    See FIGURE 2.26 STEP 4: Insert the Male Flange Component inside the Female Flange Component. The arrow, SHOR-LINE logo and notch on the Flange should be in the upward position. See FIGURE 2.27 Carefully rotate the flanges to ensure the attachment holes are parallel to the cage floor.
  • Page 17: Door Installation

    Door. Rotate the Door to the open position to ensure free movement, yet the Door Hinge Screw should be tight enough to hold the door in any position. FIGURE 2.32 - Door Hinge Assembly Shor-Line.com...
  • Page 18 FIGURE 2.33 - Quick Release Assembly STEP 5: Thoroughly clean both Cages and the Portal to ensure the removal of all chemicals and metal shavings before allowing the Cages to become occupied. STEP 6: Reattach the Cage Doors. FIGURE 2.34 - Secure Door Shor-Line.com...
  • Page 19: Section Three, Operation & Maintenance Portal Use And Care

    A pin is provided to lock the door in the closed position. Remove the pin from the stowed position, close the door and insert the pin through the Lock Hole. See FIGURE 3.3 LOCK HOLE LOCK PIN FIGURE 3.3 - Door Lock Shor-Line.com...
  • Page 20: General Maintenance & Care

    Shor-Line Technical Services for direction. Do NOT attempt to repair hydraulic leaks. Care Recommendations Routine product care will extend the quality and life of Shor-Line products and aids in protecting animals from transmittable diseases and infections. It is the owners responsibility to set-up scheduled cleaning programs, depending on use of the equipment.
  • Page 21: Section Four, Terms & Conditions

    Customer must report any concealed damage within 15 days after receipt of the shipment. Such report is to be made directly to Shor-Line's Traffic Department who will file a claim with the carrier. All packaging and contents must be held for this inspection.
  • Page 22 Return Policy & Repairs - All products being returned for any reason or delivered for repair service (whether or not pursuant to the Limited Warranty) must receive advance authorization from Shor-Line. Customer must contact Shor-Line's Technical Service Department at 1.800.444.1579 to receive a Return Authorization Number. All products returned, except for warranty service or pursuant to the Product Satisfaction policy, are subject to a minimum 15% restocking charge.
  • Page 23: Limited Warranty

    SECTION FOUR Limited Warranty In the event the Customer is not fully satisfied with the quality or workmanship of a product, SHOR-LINE in its sole discretion may arrange either to credit Customer's account (excluding shipping and handling costs) or replace the product.
  • Page 24: Contact Information

    Contact Information SHOR-LINE SHOR-LINE LIMITED Schroer Manufacturing Company Vale Business Park Llandow, 511 Osage Ave. Vale of Glamorgan CF71 7PF Kansas City, Kansas 66105, USA United Kingdom PHONE: 800.444.1579 PHONE: +44 1446 77 20 41 LOCAL: 913.281.1500 FAX: +44 1446 77 36 68 FAX: 913.281.5339...

Table of Contents