Related Manuals for Matan Barak Series
Summary of Contents for Matan Barak Series
- Page 1 Installing the Linear Encoder (3 m and 5 m Printers) Technical Note – 10100139 Rev. C 10100139 - C © Matan Digital Printers Ltd. Page 1 of 13...
-
Page 2: Safety Procedures
Spring Washer M4 55500089 55500089 Flat Washer M4 55500185 55500185 T-nut M6 33300762 33300762 Bracket 33300754 33300754 Bracket 22200866 22200866 Jig for sticking Scale 55500035 55500035 Spring Washer M3 10100139 - C © Matan Digital Printers Ltd. Page 2 of 13... - Page 3 You will also need Loctite #222. The Encoder Magnetic Scale The Encoder Converter & Reader Connecting Plate Bracket for Converter CON Screw T-nut Clamp Encoder Clamp Kit 10100139 - C © Matan Digital Printers Ltd. Page 3 of 13...
- Page 4 2. Manually move the C to the middle of the printer. ARRIAGE 3. Hold one end of the E , with the adhesive strip facing down. NCODER CALE 10100139 - C © Matan Digital Printers Ltd. Page 4 of 13...
- Page 5 CALE ARRIAGE Carriage Encoder Scale Sellotape The encoder magnetic scale appears to the right of the Carriage 7. Remove the Sellotape from the end of the S CALE 10100139 - C © Matan Digital Printers Ltd. Page 5 of 13...
- Page 6 12. Using the jig to keep it in the right position, stick the M along AGNETIC CALE the entire B , and at the same time, remove the protective tape of the adhesive strip, as shown below. 10100139 - C © Matan Digital Printers Ltd. Page 6 of 13...
- Page 7 The right end of the Beam 15. Secure the left end of the S to the B , in the same way that you CALE secured the right side. 10100139 - C © Matan Digital Printers Ltd. Page 7 of 13...
- Page 8 Aligning the sensor and the bracket on a flat surface 3. Using two screws, washers and spring washers, attach the B to the RACKET , as shown below. ARRIAGE 10100139 - C © Matan Digital Printers Ltd. Page 8 of 13...
- Page 9 NCODER EADER RACKETS ENCODER READER electronic box over the right BCC card, and connect the new E NCODER connectors instead of the old connectors, as shown below. EADER 10100139 - C © Matan Digital Printers Ltd. Page 9 of 13...
- Page 10 CALE then remove the gauge. Adjusting the height between the encoder reader and the magnetic scale to 0.5mm 10100139 - C © Matan Digital Printers Ltd. Page 10 of 13...
- Page 11 If the last print is larger than the first one – the L is not INEAR NCODER enabled, re-check the option box in the E window. NGINEER 10100139 - C © Matan Digital Printers Ltd. Page 11 of 13...
- Page 12 158.045 158.75 1PassFine 316.089 317.5 2Pass 158.045 158.75 2PassFine 316.089 317.5 2PassCoarse 316.089 317.5 3Pass 632.178 4Pass 316.089 317.5 4PassFine 632.178 5Pass 632.178 5PassPDS 316.089 317.5 9Pass 632.178 10100139 - C © Matan Digital Printers Ltd. Page 12 of 13...
-
Page 13: Document History
Ronen Shalil 20-06-11 Update Head Office Matan Digital Printers Ltd., 14 Amal Street, Park Afek, Rosh Ha'ayin 48092, Israel. Tel: (+972) 3 9002720 Fax: (972) 3 9002721 Email: support@matanprinters.com U.S. Office Matan USA Inc., 90, Earhart Drive, Suite 4, Williamsville NY 14221.