Advertisement
Advertisement
Related Manuals for Husqvarna LT 8005
Summary of Contents for Husqvarna LT 8005
- Page 1 LT 8005 Operator's manual 2-16...
-
Page 2: Table Of Contents
Contents Introduction..............2 Transportation, storage and disposal......12 Safety................4 Technical data.............. 13 Operation................ 8 EC Declaration of Conformity........16 Maintenance..............9 Introduction Product description pipes or other small spaces. Examples of such work are house foundations and parking lots. Do not use the The product is a rammer for compaction of granular soil, product for other tasks. - Page 3 14. Rammer shoe Throttle control Ultra-low-sulfur diesel fuel only. The throttle control has 3 available positions: Operation mode position (A) Lift the product at this part of the safety Start position/idle speed position (B) frame. Noise emission to the environment as referred to in the EC directive.
-
Page 4: Safety
• the product has an accessory that is not from the • the product is not repaired at an approved service manufacturer or not approved by the manufacturer. center or by an approved authority. Safety Safety definitions • Keep the product clean. Make sure that you can clearly read signs and decals. - Page 5 Do not start to operate the product again until you product and operate it safely. Do not push the know that it is safe to continue. handles into the end stops more than necessary. • Put the product in an upright position before you •...
- Page 6 • Do a check of the safety devices regularly. If the safety devices are defective, speak to your WARNING: Read the warning instructions Husqvarna service agent. that follow before you use the product. Muffler • High noise levels and long-term exposure to noise can cause noise-induced hearing loss.
- Page 7 To do a check of the stop function engine oil and let the product dry before you start the engine. To start the product on 1. Start the product. Refer to • Examine the engine for leaks regularly. If there are page 8 .
-
Page 8: Operation
Operation Introduction 3. Do the start procedure again. To operate the product WARNING: Read and understand the safety 1. Set the throttle control in the operation position. chapter before you use the product. To do before you operate the product •... -
Page 9: Maintenance
2. Set the throttle control in the stop position. Maintenance Introduction Maintenance schedule * = General maintenance done by the operator. The WARNING: Read and understand the safety instructions are not given in this operator's manual. chapter before you do maintenance on the product. - Page 10 Engine maintenance Before use, After the Weekly, Yearly, each each 10 h first 20 h each 100 h 500 h Drain and clean the fuel tank. Drain water from the fuel system. Replace the fuel filter. Clean the oil filter. Do a check of the fuel injection pump.
- Page 11 2. Remove the oil drain plug. 6. Fill with new oil through the hole for the sight glass. Technical data on page 13 for the correct Refer to type of oil. 7. Install the sight glass and tighten it fully. 8.
-
Page 12: Transportation, Storage And Disposal
3. Clean the air filter housing with a brush. 5. Examine the air filter for damage. 4. Tap the air filter against a hard surface or use a 6. Discard the air filter if it is damaged. vacuum cleaner to remove the particles. CAUTION: Always replace a damaged CAUTION: Do not let the nozzle of the air filter, or the dust will go into the... -
Page 13: Technical Data
When the product is no longer in use, send it to a 3. Attach a strap to the lifting eye and to the vehicle. Husqvarna dealer or discard it at a recycling 4. Attach a strap to the lift handle and to the vehicle. - Page 14 Rammer shoe width 280 mm/11 in. Rammer shoe width 330 mm/13 in. Engine power, kW/hp @rpm 3/4 @2900 3/4 @2900 Vibration frequency, Hz/rpm 11.5/690 11.5/690 Amplitude, mm/in. 79.3/3.12 79.3/3.12 Operation speed, m/min / ft./min 11.5/37.7 11.5/37.7 Fuel tank capacity, l/qts 3.0/3.2 3.0/3.2 Engine oil capacity *, l/qts...
- Page 15 Product dimensions Height, mm/in. 1088/42.8 Length, mm/in. 796/31.3 Rammer shoe contact 0.065/0.70 / Rammer shoe width, 280/11 / 330/13 area, m /sq. ft. 0.075/0.81 mm/in. Rammer shoe length, Width, mm/in. 330/13 444/17.5 mm/in. 1167 - 003 - 09.03.2020...
-
Page 16: Ec Declaration Of Conformity
EC Declaration of Conformity EC Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Rammer Compaction Machine Brand Husqvarna Type/Model LT 8005 Identification Serial numbers dating from 2019 and onwards... - Page 17 1167 - 003 - 09.03.2020...
- Page 18 1167 - 003 - 09.03.2020...
- Page 19 1167 - 003 - 09.03.2020...
- Page 20 www.husqvarnacp.com Original instructions 1141124-26 2020-03-12...