Bosch DDW88MM65 User Manual And Installation Instructions page 7

7.4 Switching on intensive mode
If particularly strong odours or vapours develop, you
can use intensive mode.
Press repeatedly until LED 4 lights up in the LED
1.
display for intensive mode 1.
Press repeatedly until LED 5 lights up in the LED
2.
display for intensive mode 2.
a After approx. 6 minutes, the appliance automatically
switches to fan setting 3.
7.5 Switching off intensive mode
To select a fan setting of your choice, press
▶
7.6 Switching on the fan run-on
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
Note: Further settings are available in the Home Con-
nect app.
Requirement: The appliance is switched on.
Press ⁠ .
▶
a The fan run-on starts at fan setting 1.
a The Ambient Light remains switched on for ap-
prox. 10 minutes.
a The glass panel remains extended halfway.
a The appliance switches off automatically after ap-
prox. 10 minutes.
a The glass panel moves downwards and the appli-
ance closes.
7.7 Switching on automatic mode
The optimum fan setting is set automatically using a
sensor.
Requirement: The appliance is switched on.
Press ⁠ .
▶
Note: In automatic mode, the Guided Air function is al-
ways switched on.
7.8 Switching off automatic mode
Press ⁠ .
▶
a The appliance starts at fan setting 2.
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
Note: Further settings are available in the Home Con-
nect app.
7.9 Intermittent ventilation
With interval ventilation, the ventilation system switches
on and off in the selected setting for the selected time.
Note: This function is only available in the Home Con-
nect app.
If the interval ventilation is switched on, LED 1 flashes.
1
Depending on the appliance specifications
7.10 Sensor control
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting is automatically switched on.
If the sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡ Default setting: Fan setting 3
¡ Lowest setting: Fan setting 1
¡ Highest setting: Fan setting 5
⁠ .
7.11 Setting the sensor control
Requirement: The appliance is switched on.
Press and hold
1.
Press
2.
Press
3.
Or wait approx. five seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
7.12 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement: The appliance is switched off.
Press and hold
1.
‒
1
‒
‒
Press
2.
Or wait approx. five seconds until the setting is
1
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
7.13 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After switching off the appliance, the upper two LEDs
for the grease filter's saturation indicator and/or the
lower two LEDs for the odour filter's saturation indic-
ator flash in the left hand control panel.
¡ A signal sounds repeatedly.
Press
▶
a The saturation indicator is reset.
1
and for approx. three seconds.
or to change the setting.
to save the setting.
for approx. three seconds.
To set circulating-air mode (Clean Air Standard
circulating-air set or Clean Air Plus circulating-air
set), press and hold ⁠ /
the LED display.
To set circulating-air mode (regenerable filter),
press ⁠ / until LED 3 lights up in the LED dis-
play.
To convert the electronic control back to opera-
tion without the air recirculation filter, press
until LED 1 lights up on the LED display.
to save the setting.
.
Basic operation en
1
until LED 2 lights up in
⁠ /
7