Page 3
Warranty The NI PXIe-8100 is warranted against defects in materials and workmanship for a period of one year from the date of shipment, as evidenced by receipts or other documentation. National Instruments will, at its option, repair or replace equipment that proves to be defective during the warranty period.
Page 4
EVALUATED OR CONTEMPLATED BY NATIONAL INSTRUMENTS, THE USER OR APPLICATION DESIGNER IS ULTIMATELY RESPONSIBLE FOR VERIFYING AND VALIDATING THE SUITABILITY OF NATIONAL INSTRUMENTS PRODUCTS WHENEVER NATIONAL INSTRUMENTS PRODUCTS ARE INCORPORATED IN A SYSTEM OR APPLICATION, INCLUDING, WITHOUT LIMITATION, THE APPROPRIATE DESIGN, PROCESS AND SAFETY LEVEL OF SUCH SYSTEM OR APPLICATION.
Page 5
Furthermore, any changes or modifications to the product not expressly approved by National Instruments could void your authority to operate it under your local regulatory rules.
Chapter 1 Introduction Benefits of PXI Express....................1-1 NI PXIe-8100.........................1-2 Description ......................1-2 Functional Overview ..................1-3 NI PXIe-8100 Functional Description ..........1-3 National Instruments Software ..................1-4 Cleaning .........................1-6 Chapter 2 Installation and Configuration Installing the NI PXIe-8100...................2-1 How to Remove the Controller from the PXI Express Chassis.......2-4 BIOS Setup Utility......................2-4...
Page 7
General Questions ......................4-1 Boot Options........................4-2 Cables and Connections ....................4-3 Software Driver Installation ..................4-3 Upgrade Information ..................... 4-4 Chapter 5 Troubleshooting Appendix A Specifications Appendix B Technical Support and Professional Services Glossary Index NI PXIe-8100 User Manual viii ni.com...
National Instruments PXIe-8100 embedded computer kit. How to Use the Documentation Set Begin by reading the NI PXIe-8100 Installation Guide, a brief quick-start guide that describes how to install and get started with your controller. This manual, the NI PXIe-8100 User Manual, contains more details about changing the installation or configuration from the defaults and using the hardware.
PXI-5 PXI Express Hardware Specification, Revision 1.0, PXI Systems Alliance • PXI-6 PXI Express Software Specification, Revision 1.1, PXI Systems Alliance • Serialized IRQ Support for PCI Systems Specification, Revision 6.0, Compaq Computer et al. NI PXIe-8100 User Manual ni.com...
Introduction This chapter provides overview information for PXI Express and the NI PXIe-8100 embedded controller. Benefits of PXI Express The PXI (PCI eXtensions for Instrumentation) industry standard, an open specification governed by the PXI Systems Alliance (PXISA), has quickly gained adoption and grown in prevalence in test, measurement, and control systems since its release in 1998.
The NI PXIe-8100 PXI Express/CompactPCI Express embedded computer is a PXI Express/CompactPCI Express-compatible system controller. The NI PXIe-8100 controller integrates standard I/O features in a single unit by using state-of-the-art packaging. Combining an NI PXIe-8100 embedded controller with a PXI Express-compatible chassis, such as the PXIe-1062Q, results in a fully PC-compatible computer in a compact, rugged package.
NI PXIe-8100 embedded computer. NI PXIe-8100 Functional Description The NI PXIe-8100 is a modular PC in a PXI Express 3U-size form factor. Figure 1-1 is a functional block diagram of the NI PXIe-8100. Following the diagram is a description of each logic block shown.
Parallel ATA interface enables transfer rates up to 17 MB/s in read and 5 MB/s in write. • The PXI Express Connector connects the NI PXIe-8100 to the PXI Express/CompactPCI Express backplane. • The Super I/O block represents the other peripherals supplied by the NI PXIe-8100.
Page 14
NI-Sync. For more information visit ni.com/pxi NI-VISA is the National Instruments implementation of the VISA specification. VISA is a uniform API for communicating and controlling USB, Serial, GPIB, PXI, PXI Express, VXI, and various other types of instruments.
NI-VISA driver for Linux and NI Modular Instruments are partially supported. For more information visit ni.com/linux Cleaning Use a dry, low-velocity stream of air to clean the NI PXIe-8100 controller. If needed, use a soft-bristle brush for cleaning around components. NI PXIe-8100 User Manual ni.com...
NI PXIe-8100 controller. Installing the NI PXIe-8100 This section contains general installation instructions for the NI PXIe-8100. Consult your PXI Express chassis user manual for specific instructions and warnings. Plug in your chassis before installing the NI PXIe-8100. The power cord grounds the chassis and protects it from electrical damage while you install the module.
Page 17
1 Protective Screw Cap (4X) Figure 2-1. Removing Protective Screw Caps Make sure the injector/ejector handle is in its downward position. Align the NI PXIe-8100 with the card guides on the top and bottom of the system controller slot. Caution Do not raise the injector/ejector handle as you insert the NI PXIe-8100.
Page 18
What if the NI PXIe-8100 does not boot? section of Chapter 5, Troubleshooting. Figure 2-2 shows an NI PXIe-8100 installed in the system controller slot of a National Instruments NI PXIe-1062Q chassis. 1 NI PXIe-1062Q Chassis 3 Injector/Ejector Rail 2 NI PXIe-8100 Controller Figure 2-2.
If the PXI Express chassis Inhibit Mode Selector Switch is not in the Default position, any attempt to shut down the NI PXIe-8100 through the push button reset or using Windows will result in the controller Power OK LED blinking. The user will be required to use the remote inhibit pin on the remote inhibit and voltage monitoring connector to turn off the chassis.
The Main setup menu reports the following configuration information: • BIOS Version and Build Date—These values indicate the version of the PXIe-8100 controller BIOS and the date on which the BIOS was built. • Processor Type, Frequency, and Number of Cores—These values indicate the type of processor used in the NI PXIe-8100 controller, the speed of the processor, and the number of processor cores.
Configuration submenu. Refer to the USB Configuration Submenu section for more information. • Serial Port Configuration—Use this setting to access the Serial/ Parallel Port Configuration submenu. Refer to the Serial Port Configuration Submenu section for more information. NI PXIe-8100 User Manual ni.com...
Certain real-time applications may require you to disable this setting to reduce loop time jitter. When the controller is configured to boot LabVIEW RT, legacy USB support is automatically disabled. • EHCI Hand-Off—This setting is for an OS without EHCI hand-off support. NI PXIe-8100 User Manual ni.com...
SCSI drives. When enabled, legacy mass storage controllers with boot support will be displayed in the Boot Option Priorities menu. The default value is Enabled. NI PXIe-8100 User Manual 2-10 ni.com...
Use this menu to enable BIOS security options. • Administrator Password—This setting specifies a password that must be entered to access the BIOS Setup Utility. If only the Administrator’s password is set, then this only limits access to the NI PXIe-8100 User Manual 2-12 ni.com...
System CMOS The NI PXIe-8100 contains memory backed up by a battery to store BIOS configuration information. Complete the following steps to clear the CMOS contents: Power off the chassis.
Page 31
IP Settings section and click the Apply button. For information about configuring network settings, refer to the Configuring Network Settings book, accessible by browsing to MAX Remote Systems Help»LabVIEW Real-Time Target Configuration»Configuring Network Settings from the Contents tab of MAX Help. NI PXIe-8100 User Manual 2-16 ni.com...
If you are not using LabVIEW RT, these switches should remain in the OFF position. The controller reads these switches only after a system reset. The NI PXIe-8100 controller includes the following LabVIEW RT configuration switches: •...
Page 33
The switches are shown in the OFF position. 1 Switch 1—Boot LabVIEW RT 3 Switch 3—Disable Startup VI 2 Switch 2—Boot Safe Mode 4 Switch 4—Reset IP Address Figure 2-4. LabVIEW RT Configuration Switches NI PXIe-8100 User Manual 2-18 ni.com...
PXI Express Chassis Configuration The PXI Express Platform Services software installed on your controller and available on the National Instruments Driver DVD or PXI Platform Services CD included with your kit automatically identifies your PXI Express system components to generate a pxiesys.ini...
PXI Express specification at www.pxisa.org Upgrading RAM You can change the amount of installed RAM on the NI PXIe-8100 by upgrading the SO-DIMM. To upgrade the RAM, remove the NI PXIe-8100 from the PXI Express chassis. Larger memory capacity will improve overall system performance.
Page 36
National Instruments has tested and verified that the DDR2 SO-DIMMs we sell Note work with the NI PXIe-8100. We recommend you purchase your DDR2 SO-DIMM modules from National Instruments. Other off-the-shelf DDR2 SO-DIMM modules are not guaranteed to work properly.
I/O Information Front Panel Connectors Table 3-1 lists various peripherals and their corresponding NI PXIe-8100 external connectors, bus interfaces, and functions. Table 3-1. NI PXIe-8100 Peripherals Overview Peripheral External Connector Description Video Intel Integrated Graphics Controller (15-pin DSUB) Serial COM1...
4.180 in. [106.16 mm] 3.727 in. [94.66 mm] 3.464 in. [87.98 mm] 2.979 in. [75.66 mm] 1.882 in. [47.81 mm] 1.104 in. [28.03 mm] 0.000 in. [0 mm] Figure 3-1. NI PXIe-8100 Front Panel Layout and Dimensions NI PXIe-8100 User Manual ni.com...
Chapter 3 I/O Information Figure 3-2 shows the location and pinouts for the VGA connector on the NI PXIe-8100. Table 3-2 lists and describes the VGA connector signals. Figure 3-2. VGA Connector Location and Pinout Table 3-2. VGA Connector Signals...
DDC Clock [SCL] COM1 Figure 3-3 shows the location and pinouts for the COM1 connector on the NI PXIe-8100. Table 3-3 lists and describes the COM1 connector signal. COM1 Figure 3-3. COM1 Connector Location and Pinout Table 3-3. COM1 Connector Signals...
Page 42
On (blinking) The controller is communicating with another computer on the LAN. (None) 10 Mbit/sec data rate is selected. 10/100/ Green 100 Mbit/sec data rate is selected. 1000 Amber 1000 Mbit/sec data rate is selected. NI PXIe-8100 User Manual ni.com...
Universal Serial Bus Figure 3-5 shows the location and pinouts for the Universal Serial Bus (USB) connector on the NI PXIe-8100. Each controller has 2 USB ports on the front panel. Table 3-6 lists and describes the USB connector signals.
– The DRIVE LED indicates when an access to the internal hard disk is occurring. Data Storage The NI PXIe-8100 has the following data storage features: • Internal Parallel ATA solid-state drive – 512 MB •...
This chapter answers common configuration questions you may have when using a NI PXIe-8100 embedded controller. General Questions What do the LEDs on the NI PXIe-8100 front panel mean? Refer to the LED status descriptions in the Front Panel Features...
An external USB floppy drive • Most PCI or PCIe-based devices that provide an Option ROM There are some limitations when booting from a USB device. The NI PXIe-8100 Note BIOS configures the USB devices so that they will work in a DOS environment.
How do I plug both a PS/2 mouse and PS/2 keyboard into the controller? The NI PXIe-8100 has no PS/2 connector, and you need to use a USB Y-splitter cable as shown in Figure 4-1, or a similar device, to connect both a PS/2 mouse and PS/2 keyboard.
Common Configuration Questions Upgrade Information How do I upgrade system memory? You can change the amount of installed RAM on the NI PXIe-8100 by upgrading the DDR2 SO-DIMMs. To upgrade the RAM, remove the NI PXIe-8100 from the PXI Express chassis.
Page 49
What Peripheral Drivers Should I Use with My PXI or VXI Controller?, at ni.com My NI PXIe-8100 does not have an internal floppy drive. Is there a way to use an external drive? Yes. The NI PXIe-8100 controller supports and can boot from USB floppy drives.
This chapter answers common troubleshooting questions you may have when using the NI PXIe-8100 embedded computer. What if the NI PXIe-8100 does not boot? Several problems can cause a controller not to boot. Here are some things to look for and possible solutions.
Page 51
As an alternative method, complete the following steps: Power off the chassis. Remove the controller from the chassis. Press the Clear CMOS button (SW2) as shown in Figure 5-1. Wait one second. Reinstall the controller in the chassis. NI PXIe-8100 User Manual ni.com...
Specifications This appendix lists the electrical, mechanical, and environmental specifications of the NI PXIe-8100 embedded controller. Features NI PXIe-8100 Intel Atom Processor D410 CPU Frequency 1.66 GHz On-die L2 cache 512 KB Single-Channel DDR2 RAM, PC2 5300 512 MB Standard...
Page 54
(at 25 °C ambient temperature) Pollution Degree ........2 Indoor use only. Clean the NI PXIe-8100 with a soft nonmetallic brush. Make sure that the device Caution is completely dry and free from contaminants before returning it to service. NI PXIe-8100 User Manual...
Page 56
EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity • EN 55011 (CISPR 11): Group 1, Class A emissions • AS/NZS CISPR 11: Group 1, Class A emissions • FCC 47 CFR Part 15B: Class A emissions • ICES-001: Class A emissions NI PXIe-8100 User Manual ni.com...
Page 58
This device contains a long-life coin cell battery. If you need to replace it, use the Return Cd/Hg/Pb Material Authorization (RMA) process or contact an authorized National Instruments service representative. For more information about compliance with the EU Battery Directive 2006/66/EC about Batteries and Accumulators and Waste Batteries and Accumulators, visit ni.com/environment/batterydirective...
Page 59
Technical Support and Professional Services Visit the following sections of the award-winning National Instruments Web site at for technical support and professional services: ni.com • Support—Technical support at includes the ni.com/support following resources: – Self-Help Technical Resources—For answers and solutions,...
Page 60
You also can visit the Worldwide Offices section of to access the branch ni.com/niglobal office Web sites, which provide up-to-date contact information, support phone numbers, email addresses, and current events. NI PXIe-8100 User Manual ni.com...
Page 62
LCD computer displays and digital projectors. It was developed by an industry consortium, the Digital Display Working Group (DDWG). Extended Capabilities Parallel. EEPROM Electronically Erasable Programmable Read Only Memory. Electromagnetic Compatibility. Electromagnetic interference. NI PXIe-8100 User Manual ni.com...
Page 64
Mean time between failure. NI-488 or NI-488.2 The National Instruments software for GPIB systems. NI-DAQ The National Instruments software for data acquisition instruments. NI-VISA The National Instruments implementation of the VISA standard—An interface-independent software that provides a unified programming interface for VXI, GPIB, and serial instruments.
Page 66
Glossary Universal Serial Bus. Volts. Video Graphics Array—The minimum video display standard for all PCs. Watts. NI PXIe-8100 User Manual ni.com...
Page 70
3-1 Serial Port Configuration menu technical support, B-1 Serial Port menu, 2-9 training and certification (NI resources), B-1 setting up the NI PXIe-8100 BIOS, 2-4 troubleshooting shock and vibration specifications, A-4 CMOS reset, 5-2 SO-DIMM logic block, 1-3...