Vector VEC1087C Owner's Manual page 3

rduow
u:sr
srtps
wttl{
EATITRy rs
msrAr.r.tD
ril
vlHrot.
A spARr(
rrAR
BArrERy mAy
clusr
BATrrRy
Exprosrot{.
IO
REDUG RISI(
OT
A
SPARI(
l{tAR
BATTTRY:
L,
Position
AC ond
DC
cords/cobles to reduce risk of domoge by hood, door, or other moving engine ports.
2.
Stoy cleor
of fon
blodes, belts, pulleys, ond other porls thot con couse iniury.
3.
Check
R,:,.;?t;rl
bottery posls.
POSITIVE
(POS,
P,
+) boitery post usuolly hos lorger diometer thon
NEGATIVE
4.
Determine
which bottery post
is
orounded (connected) to
the chossis.
lf negotive posl is
grounded to
chossis (os
in
most
vehicles), see (e1.'lf
positr"ve
post is
grounded io
the chossis, see
(f[
5.
For neootive-orounded vehicle. connect
POSITIVE IREDI
clomo
from botterv choroer to
POSITIVE IPOS.P.
+l
oost
o[ botErv.
C5nneci NEGATVE (BLACKI clomo
io
vehicle c]iossis
o, enoln. blick owov from
6qfie#
Do'not
connect
llomp lo corburelor, fudl lines,'or sheet-metol body ports. ConXect
to heovy giruge metol pbrt o[
the
rome or
engtne
DtocK.
6.
For oositive-orounded vehicle. connect NEGATIVE
(BlACKl clio lrom bofierv choroer to
NEGATIVE
(NEG. N. -l
oost'of
botte"rv. Connect
POSflVE
(REDI
clomo to vehicle
chLssis
or enoiie
bloc'k
owoy from bottbrv. Do iroi
tonnect clom;i lo corburelor, fuel lines, or
she<it-metol
body porls. Conn&t to o heory gouge
metol p'ort
of
the
rome or
engrne blocl(.
7.
When
disconnecting chorger, disconnect
AC
cord first. Then remove clomps
from
vehicle chossis
from
boHery terminol.
8.
Refer
to
operoting instructions for length of chorge informotion.
9.
Do not chorge the bottery while the engine
is
operoting.
tOllOW
THEST
STTPS
WHtl{
BATITRY
IS
I]ISTAII.TD OUTSIDT
YTHIq.t. A
SPARI(
I{TAR
BATTTRY
MAY
CAUSE BATITRY
TXPTOSIOI{.IO
RTDUG RISI(
OT
A
SPARI( I{TAR
BATTTRY:
l.
Check
poloritv of bofiery
posts
for top-mounted bottery conneclors, the
Positive posts
(morked POS,B +l
usuolly
hos
o lirroer diometer thbn
the
Neootive botterv oost (rirorked NEG.
N.-1.
For side-mounled bottery
connectioni,
the
side-ilounted bottery connecti6ns, the
Positi'ie
teiminol
is red,
ihe'Negotive terminol is block.'
2.
Aftoch
o 26-inch (minimum length) 6 AWG insuloted bottery coble to the Negotive bottery post (morked NEG,
N,-).
3.
Connect the Positive
(REDI bottery clomp to the
Positive
bottery connector (mqrked POS,B + or
red).
4.
Stond os
for bock from
the
bottery os possible, ond do not foce bottery when moking finol connection.
5.
Corefully connect lhe NEGATIVE (BLACK) chorger clomp
lo
the
free end o[ the bottery coble connected to the
negoiivri terminol.
6.
Set
the chorge role
ic
oppropriole selling occording
trc
bottery size.
7.
When
disconnecting chorger,- olwoys
do
so
in
reverse sequence
of
connecting procedure
ond
breok first
connection
while os hrr owoy from bottery os procticol.
8.
A
morine,(boot)
fgttery
m.usl
be
removed
ond chorged on shore.
To
chorge it on boord requires equipment
specrolly desrgned
tor monne
use.
NOIE:
This equipment hos been
teshed
ond found to comply wilh the limits for
o
Closs B
digitol
device, pursuont to
Port
l5
of the
FCC Rules. These
limits ore designed
hc
prwide reosonoble protection ogoinst hormful interlerence in
o
residentiol instollotion. This equipment generotes, uses
ond con rodiole rodio
frequency energy
ond,
i[
not
instolled ond
used
in occordonce with the
instruclions,
moy couse hormful interhrence to rodio communicolions.
However,
fiere
is no guorontee thot inlerference
will
not occur in
o
porticulor instollotion.
lf
this equipment
doei
couse
hormful interferince to rodio or television reception, which con be determined by turning the equipment off
ond on, the user is encouroged to
try to
correct
lhe interference by one or more o[ the following
meosures:
-
Reorienl
or relocote lhe receiving ontenno
-
lncreqse the seporotion between the equipment ond receiver
- Connect the equipment to on ouflet on o circuil different from
fiot
to
which the receiver
is
connecEd
- Consult the deoler or on experienced rodio/TV technicion for help
E