Vector VEC1088 A Owner's Manual & Warranty Information
  1. Manuals
  2. Brands
  3. Vector Manuals
  4. Battery Charger
  5. VEC1088 A
  6. Owner's manual & warranty information

Vector VEC1088 A Owner's Manual & Warranty Information

Smart automatic, 12 volt 2/6/12 ampere charge rates with alternator voltage check and battery recondition functions
Hide thumbs
Table of Contents

Advertisement

Quick Links

OWNER'S MANUAL & WARRANTY INFORMATION
12 VOLT 2/6/12 AMPERE CHARGE RATES WITH
ALTERNATOR VOLTAGE CHECK AND BATTERY RECONDITION FUNCTIONS
• IMPORTANT SAFETY INSTRUCTIONS •
WARNING – RISK OF EXPLOSIVE GASES
1. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES
GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS
REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR
CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
2. To reduce risk of battery explosion, follow these instructions and those published by the battery
manufacturer and manufacturer of any equipment you intend to use in vicinity of battery. Review
cautionary markings on these products and on engine.
GENERAL BATTERY SAFETY
1. Use this charger for charging a 12 VOLT LEAD-ACID battery only. It is not intended to supply power to a low voltage
electrical system other than in automotive applications. DO not use this battery charger for anything other than 12
volt rechargeable types of batteries. Charging batteries with other voltage ratings or "non-rechargeable" may burst
and cause injury to persons and damage to property.
2. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric
shock, or injury to persons.
3. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.
4. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in
a risk of fire and electric shock.
If extension cord must be used, make sure:
a. Pins on plug of extension cord are the same number, size, and shape as those of plug on charger.
b. Extension cord is properly wired and in good electrical condition; and
c. Wire size is AWG#14 (14 gauge) to 100 feet and AWG#12 for distances over 100 feet.
5. Do not operate charger with damaged cord or plug - replace the cord or plug immediately.
6. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in anyway; take it to
a qualified service technician.
7. Do not disassemble charger; contact a qualified service technician when service or repair is required. Incorrect
reassembly may result in risk of electric shock or fire.
8. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning
off charger controls will not reduce this risk.
9. Do not operate charger in rain or snow or use when wet .
10. Never charge a frozen battery.
SAVE THESE INSTRUCTIONS:
This manual contains important safety and operating instructions for battery charger Model VEC1088 A
SMART AUTOMATIC

BATTERY CHARGER

This device complies with Part 15 of the FCC Rules.
VEC1088 A

Advertisement

Table of Contents
loading

Related Manuals for Vector VEC1088 A

Summary of Contents for Vector VEC1088 A

  • Page 1: Battery Charger

    9. Do not operate charger in rain or snow or use when wet . 10. Never charge a frozen battery. This device complies with Part 15 of the FCC Rules. SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions for battery charger Model VEC1088 A...

  • Page 2: Ground And Ac Power Cord Connection

    GROUNDING PIN (A) GROUNDING MEANS USE OF AN ADAPTER IS NOT ALLOWED IN CANADA. IF A GROUNDING TYPE RECEPTACLE IS NOT AVAILABLE, DO NOT USE THIS APPLIANCE UNTIL THE PROPER OUTLET IS INSTALLED BY A QUALIFIED ELECTRICIAN VEC1088 A REV101103...

  • Page 3: Charger Location

    When disconnecting charger, disconnect AC cord first. Then remove clamps from vehicle chassis from battery terminal. h. Refer to operating instructions for length of charge information. i. Do not charge the battery while the engine is operating. VEC1088 A REV101103...

  • Page 4: Introduction And Features

    INTRODUCTION AND FEATURES Thank you for selecting the Vector Model VEC1088 A 2/6/12 Amp 12 Volt Smart Battery Charger, with Alternator Voltage Check and Battery Recondition functions. With proper care and use, it will give you years of dependable service. This battery charger has a high charge rate of up to 12 amps, and low charge rate of up to 2 amps.

  • Page 5: Controls And Indicators

    THERE ARE NO USER-SERVICEABLE PARTS IN THIS CHARGER. IN THE EVENT OF ANY OPERATING PROBLEM THAT THE CHARGER’S BUILT-IN CIRCUIT PROTECTION CANNOT HANDLE, DO NOT OPEN THE UNIT! IT MUST BE RETURNED TO VECTOR FOR PROFESSIONAL TESTING AND REPAIR. OPENING THE UNIT WILL VOID THE MANUFACTURER'S WARRANTY.

  • Page 6: Indicators

    CHARGING COMPLETE - Indicates Battery is charged. Charging Complete LED lights at same time the digital display shows ”FUL”. ALTERNATOR GOOD - Lights when load or not load checks show the alternator is keeping up with the electrical load. VEC1088 A REV101103...

  • Page 7: Charge Rate Selection

    CHARGE RATE SELECTION VEC1088 A After charger clamps are correctly connected, plug in the charger to an AC outlet and the charger will show a circulating pattern on the Digital Display. This pattern indicates power is applied. Press the ON/OFF switch button to prepare the charger to change to an operating mode.

  • Page 8: Connecting If Battery Is Outside

    CHARGING TIMES The VEC1088 A, fully automatic, Smart Battery Charger will automatically adjust the charge rate as the battery becomes charged and stops charging when the battery is fully charged. For estimates of the time it takes to charge a battery refer to Appendix A for details.

  • Page 9: Alternator Voltage Check

    • Keep the charger cords loosely coiled during storage to prevent damage to the cords. • Do not use charger if cords or clamps have been damaged in any way - call Vector Technical Support Department toll-free: (866) 584-5504 to replace cords and clamps.

  • Page 10: Troubleshooting: Fault Led Lit

    Try charging another battery, if the FAULT LED does not light, then one of the above problems exists with the initial battery. Charger will not charge and the fan will not operate if there is a fault. Call Vector Technical Support toll free: (866) 584-5504.

  • Page 11: Charging Times

    Answer: approximately 4.2 hours. Always round up the charge time by 10% to ensure full charge. In most cases, battery charging times will vary depending on the age and condition of the battery. Smaller batteries should be charged at a lower rate (2 Amps) and add an extra hour to charge time. VEC1088 A REV101103...

Table of Contents