Related Manuals for CH Hanson Norse 9683124
Summary of Contents for CH Hanson Norse 9683124
- Page 1 9683124_oipm_En011_9643312.01 03/21/18 Page 1 Operating Instructions & Parts Manual Model 9683124 10˝ Bench Top Band Saw 9643312.01 0318...
- Page 2 9683124_oipm_En011_9643312.01 03/21/18 Page 2 NORSE Operating Manual & Parts List 9683124 Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! retain instructions for future reference.
-
Page 3: Getting Started
9683124_oipm_En011_9643312.01 03/21/18 Page 3 NORSE Operating Manual & Parts List 9683124 GETTING STARTED Unpack: Do not discard packing materials until after machine has been Structural Requirements inspected for damage and completeness. Locate loose parts and Make sure all supporting structures and load attaching devices are set aside. -
Page 4: Specifications
9683124_oipm_En011_9643312.01 03/21/18 Page 4 NORSE Operating Manual & Parts List 9683124 SAFETY RULES ( CONTINUED ) • Do not overreach. Keep proper footing and balance. • Never stand on tool. Serious injury could occur if tool is tipped • Wear face mask or dust mask if operation is dusty. or if blade is unintentionally contacted. -
Page 5: Centering The Table
9683124_oipm_En011_9643312.01 03/21/18 Page 5 NORSE Operating Manual & Parts List 9683124 ASSEMBLY Setting Table Square to Saw Blade Refer to Figures 2 and 3. Refer to Figures 4, 5, 6 and 8. Loosen the knob on the lower table trunnion and place a suitably sized square against the saw blade. -
Page 6: Installation
9683124_oipm_En011_9643312.01 03/21/18 Page 6 NORSE Operating Manual & Parts List 9683124 ASSEMBLY ( CONTINUED ) Guide Post Blade Tracking Install Rip Fence Adjusting and Knob Lock Knob Refer to Figure 5. • Lay the rip fence onto the guide rail. Adjust the rip fence parallel to the saw blade. -
Page 7: Extension Cords
9683124_oipm_En011_9643312.01 03/21/18 Page 7 NORSE Operating Manual & Parts List 9683124 INSTALLATION ( CONTINUED ) Extension Cords • The use of any extension cord will cause some drop in voltage and loss of power. Properly Grounded Outlet • Wires of the extension cord must be of sufficient size to carry Grounding Prong the current and maintain adequate voltage. - Page 8 9683124_oipm_En011_9643312.01 03/21/18 Page 8 NORSE Operating Manual & Parts List 9683124 OPERATION ( CONTINUED ) Changing and Adjusting the Saw Blade This band saw is factory-equipped with a general-purpose wood • Always hold material firmly and feed it into the blade at a cutting blade;...
-
Page 9: Tracking The Saw Blade
9683124_oipm_En011_9643312.01 03/21/18 Page 9 NORSE Operating Manual & Parts List 9683124 OPERATION ( CONTINUED ) 5. Loosen the thrust bearing's lock screw. 6. Adjust thrust bearing position (distance thrust bearing - band Tracking the Saw Blade saw blade = 0.5 mm – if the band saw blade is turned by hand, Refer to Figure 13. -
Page 10: Basic Alignment
9683124_oipm_En011_9643312.01 03/21/18 Page 10 NORSE Operating Manual & Parts List 9683124 OPERATION ( CONTINUED ) Basic Alignment Refer to Figures 16 and 18. Guide Open the lower housing door. Bearings 2. Loosen lower blade guide fixing-screw with an open jaw wrench. - Page 11 9683124_oipm_En011_9643312.01 03/21/18 Page 11 NORSE Operating Manual & Parts List 9683124 OPERATION ( CONTINUED ) Type of Cut • Contour cutting is done by guiding workpiece freehanded to NOTE: Do not adjust the fence handle such that excessive produce curved shapes. pressure is exerted during operation - this may lead to deformation of the end clamp at the rear of the rip fence.
-
Page 12: Maintenance
9683124_oipm_En011_9643312.01 03/21/18 Page 12 NORSE Operating Manual & Parts List 9683124 MAINTENANCE Steps required to keep the saw in optimum operating condition have been described under “Operating Instructions.” The Safety Precautions should be performed before operation. For proper maintenance: • Keep saw clean and dry. -
Page 13: Troubleshooting Guide
9683124_oipm_En011_9643312.01 03/21/18 Page 13 NORSE Operating Manual & Parts List 9683124 TROUBLESHOOTING GUIDE Symptom Possible Cause(s) Corrective Action The machine does not work when 1. No power supply. 1. Check the cable for breakage. switched on. 2. Defective switch. 2. Replace the lock switch. 3. - Page 14 9683124_oipm_En011_9643312.01 03/21/18 Page 14 NORSE Operating Manual & Parts List 9683124 REPAIR PARTS ILLUSTRATION FOR 9683124 10˝ BENCH TOP BAND SAW Figure 22 - Replacement parts illustration for 10˝ Bench Top Band Saw.
- Page 15 9683124_oipm_En011_9643312.01 03/21/18 Page 15 NORSE Operating Manual & Parts List 9683124 REPAIR PARTS LIST FOR 9683124 10˝ BENCH TOP BAND SAW Ref. Part Ref. Part No. Description Number Qty. No. Description Number Qty. Lower door 9642921.01 Angle Gauge 9642953.01 Hex. socket head bolt M6x16 Housing with nut 9642954.01 Spacer bushing...
- Page 16 9683124_oipm_En011_9643312.01 03/21/18 Page 16 NORSE Operating Manual & Parts List 9683124 REPAIR PARTS ILLUSTRATION FOR 9683124 10˝ BENCH TOP BAND SAW ( CONTINUED ) 115 114 Figure 23 - Replacement parts illustration for 10˝ Bench Top Band Saw (continued).
- Page 17 9683124_oipm_En011_9643312.01 03/21/18 Page 17 NORSE Operating Manual & Parts List 9683124 REPAIR PARTS LIST FOR 9683124 10˝ BENCH TOP BAND SAW ( CONTINUED ) Ref. Part Description Qty. Pressure plate 9642988.01 Pan.Hd.Screw M5x10 Lower Wheel 9642989.01 Pulley 9642990.01 V-Ribbed Belt 9642991.01 Hex.Nut M14x1.5 Spring Washer M14...
- Page 18 9683124_oipm_En011_9643312.01 03/21/18 Page 18 NORSE Operating Manual & Parts List 9683124 NOTES...
- Page 19 9683124_oipm_En011_9643312.01 03/21/18 Page 19 NORSE Operating Manual & Parts List 9683124 NOTES...
- Page 20 9683124_oipm_En011_9643312.01 03/21/18 Page 20 NORSE Operating Manual & Parts List 9683124 NORSE Warranty NORSE by C.H. Hanson warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or otherwise altered, or used for a purpose other than that for which it was intended.