Related Manuals for CH Hanson Norse 9683125
Summary of Contents for CH Hanson Norse 9683125
- Page 1 Operating Manual & Parts List 9683125 14˝ BAND SAW Read carefully and follow all safety rules and operating instructions before first use of this product. 9644165.01-0419...
-
Page 2: Getting Started
NORSE Operating Manual & Parts List 9683125 GETTING STARTED Carriage bolt (16) K Washer (16) L Nut (16) STRUCTURAL REQUIREMENTS • Operating Instructions and Parts Manual (1) not shown Make sure all supporting structures and load attaching devices are strong enough to hold your intended loads. If in doubt, consult a UNPACK: qualified structural engineer. -
Page 3: Specifications
NORSE Operating Manual & Parts List 9683125 SAFETY RULES (CONTINUED) • Adjust upper guide to just clear workpiece. • Hold workpiece firmly against table. • DIRECTION OF FEED: Feed work into a blade or cutter against PREPARE WORK AREA FOR JOB the direction of rotation of the blade or cutter only. - Page 4 NORSE Operating Manual & Parts List 9683125 ASSEMBLY (CONTINUED) 2. Tighten the hex nut and recheck the saw blade and the table for squareness. 3. Lock the table into position and check that the indicator reads 3. Attach the two braces (Ref. No. 2) to the top front and bottom zero degree on the side of lower table trunnion.
- Page 5 NORSE Operating Manual & Parts List 9683125 ASSEMBLY (CONTINUED) Blade Tension Quick Release ATTACH DRIVE BELT TENSION HANDWHEEL Lever Refer to figure 8. 1. Place handwheel assembly onto shaft. Blade Guide Height Adjust- 2. Secure in position with set screw. ment Knob and Lock Tracking...
- Page 6 NORSE Operating Manual & Parts List 9683125 INSTALLATION (CONTINUED) EXTENSION CORDS • The use of any extension cord will cause some drop in voltage and loss of power. This tool is equipped with an approved 3-conductor cord rated at • Wires of the extension cord must be of sufficient size to carry 150V and a three prong grounding type plug or your protection the current and maintain adequate voltage.
- Page 7 NORSE Operating Manual & Parts List 9683125 OPERATION (CONTINUED) Blade Tension Knob • Make sure that the blade tension and blade tracking are prop- erly adjusted. • Make “relief” cuts before cutting long curves. • Release blade tension when the saw will not be used for a long period of time.
- Page 8 NORSE Operating Manual & Parts List 9683125 OPERATION (CONTINUED) BLADE SPEED ADJUSTMENT Refer to Figure 21 3. Adjust the rear roller guide to be just clear of the back of the WARNING: Make certain that saw is disconnected from the power saw blade by unlocking the set screw (D) located on rear of source before attempting to change the blade speed.
- Page 9 NORSE Operating Manual & Parts List 9683125 OPERATION (CONTINUED) MITER GAUGE Use miter gauge for securing and holding workpiece at desired angle to produce angled cuts. Use scale to adjust gauge to desired BLADE PITCH angle. • Pitch describes number of teeth per inch or tooth size. A blade WARNING: with more teeth per inch produces a smoother cut.
-
Page 10: Troubleshooting
NORSE Operating Manual & Parts List 9683125 TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION The machine does not work when 1. No power supply. 1. Check the cable for breakage. switched on. 2. Defective switch. 2. Replace the lock switch. 3. Defective motor. 3. - Page 11 NORSE Operating Manual & Parts List 9683125 Figure 24 - Replacement Parts Illustration For Stand...
- Page 12 NORSE Operating Manual & Parts List 9683125 Figure 22 - Replacement Parts Illustration for Frame and Drive...
- Page 13 NORSE Operating Manual & Parts List 9683125 REPLACEMENT PARTS LIST FOR FRAME AND DRIVE Ref. Ref. Description Part No. Qty. Description Part No. Qty. Lower Door Assembly 9636492.00 Wing Nut 9636513.00 Upper Door Assembly 9636493.00 6mm Flat Washer 3AMI-18 Retaining Ring 9606169.00 6-1.0 x 10mm Hex Head Bolt Upper Wheel Shaft...
- Page 14 NORSE Operating Manual & Parts List 9683125 Figure 23 - Replacement Parts Illustration For Table...
- Page 15 NORSE Operating Manual & Parts List 9683125 REPLACEMENT PARTS LIST FOR TABLE Ref. Ref. Description Part No. Qty. Description Part No. Qty. 4.8 x 16mm Tap Screw 9631663.00 Locking Handle 9636453.00 Plate 9636427.00 Spacer 9636454.00 Rack 9636428.00 Lower Blade Guard 9636462.00 Guide Post 9636429.00...
- Page 16 NORSE Operating Manual & Parts List 9683125 NORSE WARRANTY NORSE by C.H. Hanson warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or otherwise altered, or used for a purpose other than that for which it was intended.
Need help?
Do you have a question about the Norse 9683125 and is the answer not in the manual?
Questions and answers