Canceling A Cycle; Changing A Cycle Or Setting; Adding Items During A Cycle; Option Selections - Whirlpool 941 Series Use And Care Manual

Use this cycle for rinsing
dishes, glasses, and
silverware that will not be
washed right away.
Pre- Rinse Main Rinse
Wash Wash
† A small amount of water runs through the pump to remove soil
particles.

Canceling a Cycle

Anytime during a cycle, press
Cancel/Drain glows. The dishwasher pauses for about 5 seconds
and starts a 2-minute drain (if needed). Let the dishwasher drain
completely. The light goes off when the dishwasher finishes the
drain.
To stop the drain
You can press Cancel/Drain again to stop the drain immediately.
Remember to drain the dishwasher before starting a new cycle.
NOTE: A small amount of water remains in the dishwasher. This
is normal.
To clear the indicators
Press Cancel/Drain before starting the dishwasher to clear all
options and cycles.

Changing a Cycle or Setting

During the first minute of a cycle
Press a new cycle and/or options.
After the first minute of a cycle
1. Press
Cancel/Drain glows. The dishwasher pauses for 5 seconds
and starts a 2-minute drain (if needed). Let the dishwasher
drain completely.
2. Check the detergent dispensers. If the main wash cup has
opened and the detergent washed away, refill the cups as
needed.
3. Close the door.
4. Press a new cycle and/or options.
Do not use
detergent
with this
cycle.
Purge † Final Dry Time
Rinse (min)
10

Adding Items During a Cycle

You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the main wash
section is still closed, you can add items.
To add items
1. Lift up the door latch to stop the cycle. Wait for the spraying
Water
action to stop before opening the door.
Usage
2. Open the door. If the main wash detergent dispenser is still
(gal/L)
closed, add the item.
2.2/10.0
3. Close the door, but do not latch it. Wait 30 seconds for the air
in the dishwasher to warm up. This reduces the amount of
moisture escaping from the vent when restarting a cycle.
4. Close the door firmly until it latches. The dishwasher resumes
the cycle after about a 5-second pause.
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn the option off.
Select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
any time before drying begins.
After a wash cycle, the dishwasher remembers the options used
and uses the same options in the next wash cycle, unless you
select new options or press Cancel/Drain.
Hi-Temp Scour
Select this high-temperature option for improved cleaning of
heavily soiled dishes. Selecting this option adds heat, water and
time to the wash cycle. Heating the water helps improve washing
results.
The Pots & Pans cycle, with the Hi-Temp Scour feature, is
recommended for baked-on soil.
NOTE: The Hi-Temp Scour feature is an option with Normal
Wash, Heavy Wash, and Pots & Pans.
SANI RINSE™ Option (on some models)
Select this option to raise the water temperature in the final rinse
to approximately 155°F (68°C) for 10 minutes. The SANI RINSE
option adds heat and time to the cycle. In the Normal Wash,
Heavy Wash, and Pots & Pans cycles, this high-temperature rinse
sanitizes your dishes and glassware in accordance with NSF/
ANSI Standard 184 for Residential Dishwashers. Certified
residential dishwashers are not intended for licensed food
establishments.
NOTE: Use the SANI RINSE option with the Normal Wash, Heavy
Wash, and Pots & Pans cycles. Only these sanitization cycles
have been designed to meet the NSF/ANSI requirements.

Option Selections

15