Page 1
UP POE HAT Maker Board UP-POE01 User’s Manual 1 Last Updated: July 6, 2020...
Page 2
Copyright Notice This document is copyrighted, 2020. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer.
Page 3
Acknowledgement All other products’ name or trademarks are properties of their respective owners. Intel® is a registered trademark of Intel Corporation ⚫ ITE is a trademark of Integrated Technology Express, Inc. ⚫ IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines ⚫...
Page 4
Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity UP-POE01 POE HAT Board ⚫ If any of these items are missing or damaged, please contact your distributor or sales representative immediately. Preface...
Page 5
About this Document This User’s Manual contains all the essential information, such as detailed descriptions and explanations on the product’s hardware and software features (if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product. Users may refer to the product page on AAEON.com for the latest version of this document.
Page 6
Safety Precautions Please read the following safety instructions carefully. It is advised that you keep this manual for future references All cautions and warnings on the device should be noted. Make sure the power source matches the power rating of the device. Position the power cord so that people cannot step on it.
Page 7
If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii. Exposure to moisture Device is not working as expected or in a manner as described in this manual The device is dropped or damaged Any obvious signs of damage displayed on the device...
Page 8
FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
Page 10
China RoHS Requirement (EN) Poisonous or Hazardous Substances or Elements in Products AAEON Main Board/ Daughter Board/ Backplane Poisonous or Hazardous Substances or Elements Hexavalent Polybrominated Polybrominated Component Lead Mercury Cadmium Chromium Biphenyls Diphenyl Ethers (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) PCB &...
Specifications System LT4321I (PoE Ideal Diode Bridge Controller) x 1 LT4276B (PD Forward / Flyback Controller) x 1 I/O Placements External Ports RJ45 input x 1 RJ45 output x 1 Internal connector HAT 40 GPIO male (5V, GND) x 1 Miscellaneous Form Factor 3.37"...
Jumpers and Connectors List of Switches and Connectors Please refer to the table below for all of the board’s jumpers that you can configure for your application Label Function Connector Type HAT1 5V Out Header 22N8562-40SA2B-01G POE1 Ethernet Input Connector RT5-1640K22A LAN1 Ethernet Output Connector...
Block Diagram Installation Guide This section details how to connect the UP POE HAT Board with your UP Main Board. UP POE HAT can be used with UP Board or UP Squared. Connect Main Board (MB) and POE board through 40-pin HAT connector. Use standoffs and screws in accessory kit to secure the boards together.
Page 21
The POE HAT will power your MB through the 40PIN header and transmit the LAN signal to your MB via the LAN cable. To power other devices while using the POE HAT, connect devices to the 5V DC Out port instead of the 40-pin header. Note: Do not connect the UP Board or UP Squared 5V DC PSU while using the PoE HAT! Chapter 3 –...