Subscribe to Our Youtube Channel
Related Manuals for LG LV640S-Z
Summary of Contents for LG LV640S-Z
- Page 1 INSTALLATION MANUAL LED TV* Please read this manual carefully before operating your set and retain it for future reference. LV640S-Z/T/G/D* www.lg.com...
-
Page 2: Table Of Contents
Type of Connector : D-Sub 9-Pin Male INSTALLATION MENU RS-232C Configurations Command Reference List INTRODUCTION IR OUT Using Guide LG HOTEL MODE Transmission / Receiving Protocol - Hotel Mode Operation - Power On Status - Volume - Key Management - Limited Mode... -
Page 3: Using The Button
USING THE BUTTON USING THE BUTTON Basic functions <A/B type> Power On (Press) Power Off (Press and hold) Volume Control Programmes Control <C type> Power On (Press) Power Off (Press and Hold) Menu Control (Press Menu Selection (Press and Hold 1 All running apps will close, and any recording in progress will stop. -
Page 4: Ezmanager
EZMANAGER EZMANAGER • Image shown may differ from your TV. • LANGUAGE & COUNTRY SELECTION - Please select the Language and Country. Some countries need to select the Time Zone. -
Page 5: Installation Menu
The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’ . The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and convenient operation for Hotelier and System Integrators. -
Page 6: Lg Hotel Mode
INSTALLATION MENU LG HOTEL MODE Use the button to select the LG HOTEL MODE SETUP. Use the ‘OK’ button and then button to select Hotel Mode Operation. - When ‘Hotel Mode Operation’ is set to On (Work), all functions of Hotel Mode apply. -
Page 7: Volume
Operation’ will be worked by below. IR Operation y Decide whether work the LG remote control or not. - When ‘IR Operation’ is set to 'Normal' , all remote keys are available. - 'Use PWR Only' makes block all remote keys except power key. -
Page 8: Limited Mode
INSTALLATION MENU Limited Mode - Configure TV function’s limitation. When selected to ‘On’ , following sub-menus will be worked by below. Setup Menu - Permit to tune and manage programmes as 'On'(permitted) or 'Off'(not permitted). Programme Change y Decide to change channel or not by setting ‘Program Change' as ‘On’(Change Possible) or ‘Off’(Change Impossible) when present source is TV. -
Page 9: Power On Default
INSTALLATION MENU Power On Default - Set the channel to display and Volume Level, etc. when turn on power in AC Power On or Stand-by status. - Set to On(Work) or Off(Do Not Work). - When ‘Power On Default’ is set to Off, it is not applied to the subordinate Input, Programme, A/V Setting, Aspect Ratio menu. -
Page 10: Network
INSTALLATION MENU NETWORK button to select the NETWORK. Use the MAC Address - Displays the MAC address (not customizable). Network Setting One-click network connection - Connects easily to a wired/wireless network. - Network Connection to connect to an available network automatically. Follow the prompts on the TV. To connect to a network through Set Expert - For use in special circumstances such as in offices (in cases where a static IP is used). -
Page 11: Wake On Lan
INSTALLATION MENU Wake On LAN y Sets the Wake On LAN function to Enable or Disable. - The Wake On LAN feature enables the TV to receive software updates and/or be powered ON upon receipt of Wake Up Frame packets and/or Magic Packet data via the wired LAN. To facilitate use of this feature, note that the appropriate wired connection must be made. -
Page 12: General
INSTALLATION MENU GENERAL Configuration Setup Select RCU - It is a mode to set whether to use Select RCU or not. When ‘Select RCU’ is set to ‘Enable’ , You can adjust ‘Number of RCU’ menu. Number of RCU - It is a mode to set Number of RCU. Number of RCU value range 1~9. - Page 13 INSTALLATION MENU On Timer Operation - It is a mode to select ‘On Timer Operation’ working one time or repeatedly. 'Once': ‘On Time’ in the user menu operates only one time when the ‘On Time’ menu is set to ‘ON’ . ‘Repeat’...
-
Page 14: External Speaker
INSTALLATION MENU External Speaker Volume Control - Selects the volume control method of an external speaker. You can select ‘Off’ , ‘Int Variable’ , ’ Fixed.’ , ’Ext Variable’ by pressing button. Ext Variable uses the External Vol Up/Down Control Line to change the volume up to 1 Watts. Int variable is linked to the main volume OSD and change the volume 0 - 1 Watts. -
Page 15: Password Change
INSTALLATION MENU Password Change - To ensure more security, Password can be changed by installers’ own design. Change password by using virtual keyboard. Input the password again for confirmation. PreLoaded App If you want to use a particular app, you can choose from the menu. you can setting each apps activation. You can check or uncheck by pressing ‘OK’... -
Page 16: Media Share
INSTALLATION MENU MEDIA SHARE ► You can setting Whether to use for “SmartShare” Screen Share - Screen Share enables WiFi p2p functions such as Miracast and WiDi. If this value is enabled, Screen Share app is displayed at launcher bar and User can connect to TV by user’s Miracast enabled mobile phone or WiDi enabled laptop DIAL - With this DIAL service, you can launch the target app at Smart Home Launcher bar without select the target app by remote controller. - Page 17 INSTALLATION MENU Use Default - If you want to use default password(this password was generated randomly), you must select ‘Enable’ in this item. Security Key - When guests want to use TV’s SoftAP function, they need this password. If you want to change this default password, you need to Change ‘Use Default’...
-
Page 18: Tv Manager
INSTALLATION MENU TV MANAGER USB Download Menu * USB Cloning : An Installer can quickly set up and clone multiple TV sets at a property. These cloned TVs will all have the same Master TV Setup: Public Display Mode Installation Menu settings, User A/V settings and the Channel Map. This newer procedure significantly decreases the installation time that would be necessary if the standard RS-232C method were used instead. - Page 19 INSTALLATION MENU Ez Download - Ez Download is a function that enables users to download the desired items all at once, such as EPK (software update file), TLL, Logo Image, Background Images, Micom. * Images and EPK files should be copied into the folder named LG_DTV on the USB. - TLL files should be copied to the root folder of the USB.
- Page 20 INSTALLATION MENU Logo Image Download - If there are more than two USB Memory Device, It is possible to select the USB. - The download sequence is Logo Image Download -> Select Image -> UPDATE. NOTE Splash Image update function supports only JEPG,BMP format file of less than 8 MB filesize. We recommend you that splash image resolution match the TV`s panel resolution.
- Page 21 INSTALLATION MENU Insert Background Image(s) - This feature downloads Insert Background Image(s) from USB. - Images should be copied to LG_DTV of the USB. - The download sequence is Insert Background Image(s) -> Select Images -> UPDATE. NOTE Maximum number of images that you can update at once are 12. If you updates the images, original images will be removed.
- Page 22 INSTALLATION MENU Update TV Software - This feature update EPK of TV through the hex file in USB. The target file is located in \LG_DTV folder. - If there are more than two USB memory Device, It is possible to select the USB. - The download sequence is Update TV Software ->...
- Page 23 INSTALLATION MENU Update Micom Software - This feature update MICOM of TV through the txt file in USB. The target file is located in \LG_DTV folder - If there are more than two USB memory Device, It is possible to select the USB. - The download sequence is Update Micom Software ->...
- Page 24 INSTALLATION MENU Import Clone File - Once the internal TV data and its channel map information is written to the USB memory card, the user can start “Import Clone File” process with the data file generated and stored in USB memory card. As previously warned in “Export Clone File” process, the user should not turn TV off nor unplug the USB memory card.
- Page 25 INSTALLATION MENU Export Clone File - "Export Clone File” must be done first before “Import Clone File” process, as it generate the file to be used in “Export Clone File”. While writing is in process, the user must not turn TV off nor unplug the USB memory card. The following images might be slightly different than the OSD image.
-
Page 26: Ir Codes
IR CODES IR CODES • This feature is not available for all models. Code Code Function Note Function Note (Hexa) (Hexa) Remote control Button Remote control Button (POWER) (Power On/Off) Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button Remote control Button... -
Page 27: External Control Device Setup
EXTERNAL CONTROL DEVICE SETUP EXTERNAL CONTROL Phone jack Type (TV) (PC) DEVICE SETUP (Depending on model) RS-232C IN (CONTROL & SERVICE) (PC) (TV) • You need to purchase the phone-jack to RS-232C cable RS-232C Setup required for the connection between the PC and the TV, which is specified in the manual. -
Page 28: Rs-232C Configurations
EXTERNAL CONTROL DEVICE SETUP RS-232C Configurations 7-Wire Configurations (Standard RS-232C cable) D-Sub 9 D-Sub 9 3-Wire Configurations (Not standard) D-Sub 9 D-Sub 9 Communication Parameters • Baud rate: 9600 bps (UART) • Data length: 8 bits • Parity : None •... -
Page 29: Command Reference List
EXTERNAL CONTROL DEVICE SETUP Command Reference List (Depending on model) DATA COMMAND1 COMMAND2 (Hexadecimal) 01. Power 00 to 01 02. Aspect Ratio (See p. 31) 03. Screen Mute (See p. 32) 04. Volume Mute 00 to 01 05. Volume Control 00 to 64 06. -
Page 30: Ir Out Using Guide
If not use the remote-controller with data formats recommended, IR output signals will be suppressed automatically by IR receiver. In this case, LG does not guarantee IR working function. To make sure of this matter, here are two methods as below. -
Page 31: Transmission / Receiving Protocol
EXTERNAL CONTROL DEVICE SETUP Transmission / Receiving 1 Power (Command: k a) ►To control Power On/Off of the set. Protocol Transmission (Depending on Model) [k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off 01 : Power On Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [a][ ][Set ID][ ][OK/NG][Data][x] [Command 1] : First command to control the TV. - Page 32 EXTERNAL CONTROL DEVICE SETUP 3 Screen Mute (Command: k d) 6 Contrast (Command: k g) ►To select screen mute on/off. ►To adjust screen contrast. You can also adjust contrast in the PICTURE menu. Transmission Transmission [k][d][ ][Set ID][ ][Data][Cr] [k][g][ ][Set ID][ ][Data][Cr] Data 00 : Screen mute off (Picture on) Data Min : 00 to Max : 64 Video mute off...
- Page 33 EXTERNAL CONTROL DEVICE SETUP 10 Sharpness (Command: k k) 13 Balance (Command: k t) ►To adjust the screen sharpness. ►To adjust balance. You can also adjust sharpness in the PICTURE menu. You can also adjust balance in the AUDIO menu. Transmission Transmission [k][k][ ][Set ID][ ][Data][Cr]...
- Page 34 EXTERNAL CONTROL DEVICE SETUP 18 Tune Command (Command: m a) ►Select channel to following physical number. [q][ ][Set ID][ ][OK/NG][Data][x] Transmission [m][a][ ][Set ID][ ][Data 00][ ][Data 01][ ][Data 02][Cr] 16 Auto Configuration (Command: j u) (Only RGB support Data 00 : High channel data model) ►To adjust picture position and minimize image shaking automatically.
- Page 35 EXTERNAL CONTROL DEVICE SETUP 20 Key (Command: m c) External Input Data ►To send IR remote key code. Transmission Analogue [m][c][ ][Set ID][ ][Data][Cr] Data IR CODES Component [c][ ][Set ID][ ][OK/NG][Data][x] HDMI 21 Control Back Light (Command: m g) ►To control the backlight.
Need help?
Do you have a question about the LV640S-Z and is the answer not in the manual?
Questions and answers