Chassis Electrical Parts List - Sanyo DP19640 Service Manual

CAUTION: To Protect against electrical shock and for continued product safety, refer to SAFETY PRECAUTIONS
CAUTION: To Protect against electrical shock and for continued product safety, refer to SAFETY PRECAUTIONS
and PRODUCT SAFETY NOTICE on Page 2.
and PRODUCT SAFETY NOTICE on Page 2.
PRODUCT SAFETY SHOULD BE CONSIDERED WHEN A REPLACEMENT IS MADE IN ANY AREA OF A RECEIVER.
COMPONENTS INDICATED BY A
COMPONENTS IN WHICH SAFETY CAN BE OF SPECIAL SIGNIFICANCE. IT IS PARTICULARLY RECOMMENDED
THAT ONLY PARTS DESIGNATED ON THE FOLLOWING PARTS LIST BE USED FOR COMPONENT REPLACE-
MENT DESIGNATED BY A
BE MADE FOR REPLACEMENT ITEMS DESIGNATED BY A
Note: Schematic part location numbers may not always match with the part descriptions.
Note: Schematic part location numbers may not always match with the part descriptions.
The part descriptions are correct and should be used.
The part descriptions are correct and should be used.
Key No. Part No.
Schematic
Part No.
Location
CAPACITORS
CAPACITORS
NOTES:
Read description of the Capacitor as follows:
(Example)
CERAMIC 100P K 50V
Tolerance Symbols:
Less than 10pF
A : Not specified B : ±0.1pF
D : ±0.5pF
G : ±2pF
R : ±0.25 -0pF
More than 10pF
A : Not specified B : ±0.1%
D : ±0.5%
H : ±3%
L : ±15%
P : +100-0%
U : +75-10%
X : +40-20%
Rated value: P=pico farad, U=micro farad
Material:
CERAMIC........... Ceramic
MT-PAPER......... Metallized Paper
POLYESTER...... Polyester
MT-POLYEST.....Metallized Polyester
POLYPRO.......... Polypropylene
MT-POLYPRO....Metallized Polypropylene
COMPO FILM.....Composite film
MT-COMPO........Metallized Composite
STYRENE...........Styrene
TA-SOLID........... Tantalum Oxide Solid Electrolytic
AL-SOLID........... Aluminium Solid Electrolytic
ELECT................ Aluminum Foil Electrolytic
NP-ELECT..........Non-polarised Electrolytic
OS-SOLID.......... Aluminium Solid with Organic Semiconductive Electrolytic
RESISTORS
NOTES:
Read description of the Resistor as follows:
(Example)
CARBON 4.7K J A
Performance Symbols:
A: General B: Non flammable
Z: Low noise
Other: Temperature coefficient
Tolerance Symbols:
A: ±0.05% B: ±0.1% C: ±0.25% D: ±0.5%
F: ±1%
M: ±20%
Rated value, ohms:
K: 1,000, M: 1,000,000
Material:
CARBON........... Carbon
MT-FILM............ Metal Film

CHASSIS ELECTRICAL PARTS LIST

CHASSIS ELECTRICAL PARTS LIST
PRODUCT SAFETY NOTICE
IN THIS PARTS LIST AND THE SCHEMATIC DIAGRAM DESIGNATE
. NO DEVIATIONS FROM RESISTANCE, WATTAGE, AND VOLTAGE RATINGS MAY
Description
Description
Rated Voltage
C : ±0.25pF
E : +0 -1pF F : ±1PF
H : +0.1 -0pF L : +0 -0.1pF
S : +0-0.25pF
C : ±0.25%
F : ±1% G : ±2%
J : ±5% K : ±10%
M : ±20% N : ±30%
Q : +30-10% T : +50-10%
V : +20-10% W : +100-10%
Y : +150-10% Z : +80-20%
1/4W
Rated Wattage
G: ±2% J: ±5% K: ±10%
P: +5-15%
(Example)
CERAMIC 100P K 50V
Rated value: P=pico farad, U=micro farad
Material:
CERAMIC........... Ceramic
MT-PAPER......... Metallized Paper
POLYESTER...... Polyester
MT-POLYEST.....Metallized Polyester .
POLYPRO.......... Polypropylene
MT-POLYPRO....Metallized Polypropylene
COMPO FILM.....Composite film
MT-COMPO........Metallized Composite
STYRENE...........Styrene
TA-SOLID........... Tantalum Oxide Solid Electrolytic
AL-SOLID........... Aluminium Solid Electrolytic
ELECT................ Aluminum Foil Electrolytic
Key No. Part No.
NP-ELECT..........Non-polarised Electrolytic
Schematic
Part No.
OS-SOLID.......... Aluminium Solid with Organic Semiconductive Electrolytic
Location
RESISTORS
RESISTORS
NOTES:
Read description of the Resistor as follows:
(Example)
CARBON 4.7K J A
Tolerance Symbols:
A: ±0.05% B: ±0.1% C: ±0.25% D: ±0.5%
F: ±1%
M: ±20%
Rated value, ohms:
K: 1,000, M: 1,000,000
Material:
CARBON........... Carbon
MT-FILM............ Metal Film
OXIDE-MT......... Oxide Metal Film
SOLID................ Composition
MT-GLAZE......... Metal Glaze
WIRE WOUND... Wire Wound
CERAMIC RES.. Ceramic
FUSIBLE RES.... Fusible
– 9 –
-11-
Rated Voltage
Tolerance Symbols:
Less than 10pF
A : Not specified B : ±0.1pF C : ±0.25pF
D : ±0.5pF E : +0 -1pF F : ±1PF
G : ±2pF H : +0.1 -0pF L : +0 -0.1pF
R : ±0.25 -0pF S : +0-0.25pF
More than 10pF
A : Not specified B : ±0.1% C : ±0.25%
D : ±0.5% F : ±1% G : ±2%
H : ±3% J : ±5% K : ±10%
L : ±15% M : ±20% N : ±30%
P : +100-0% Q : +30-10% T : +50-10%
U : +75-10% V : +20-10% W : +100-10%
X : +40-20% Y : +150-10% Z : +80-20%
Description
Description
1/4W
Rated Wattage
Performance Symbols:
A: General B: Non flammable
Z: Low noise
Other: Temperature coefficient
G: ±2% J: ±5% K: ±10%
P: +5-15%