AGT 5580/3 GX160 Owner's Manual page 15

Fitting the steering column (E) (Fig. 7-12)
To install the steering column (E) proceed as follows:
•
Loosen the 4 screws (7a) (Fig. 7).
•
Loosen screw (8a) and remove them (Fig. 8). Attention! Insert the pin (9a) of the steering
column
(E) into the gear selector lever (22) (see Fig.9).
•
The hole of the gear selector lever (22) and the hole of the steering column pin (9a) must be
brought into conformity and the gear selector lever must be locked by using the fastening pin
small (B7) and the split pin (see Fig.9).
•
Fit the cover (10a) of the gear selector lever with screw (10b) (Fig.10).
•
Mount the steering column (E) and fix it with the 4 screws (11a) (see Fig. 11).
•
Loosen and remove the hexagonal screw (12a) by turning it counterclockwise. Hold the support
wheel (12b) at the same time (Fig. 12).
•
Pull the support wheel (12b) from the shaft (12c) (Fig. 12).
•
Subsequently the lower hole at the gear selector lever (22) must be brought into conformity
with the hole at the pin (12d) and locked by using the fastening pin (12e) and the split pin (12f)
as shown in Fig. 12.
•
Insert the support wheel (12b) onto the shaft (12c) (Fig. 12).
Observe the correct course of the drive belts!
•
Secure the support wheel (12b) with the hexagonal screw (12a) by turning it clockwise. Hold
the support wheel (12b) at the same time (Fig. 12).
Assembling the handlebar (6) (Fig. 13-15)
Position the handlebar (6) in the seat of steering column (7) as shown in figure 13. The height of the
handlebar (6) can be adjusted to three alternative settings.
13a - High
13b - Middle
13c - Low
Lock the handlebar with the special screw (13d) and bracket (13e) if the required height is set.
ATTENTION!
Make sure you insert the hooked end of bracket (13e) in hole of the handlebar (6).
Fasten the cover of the handlebar fixing (D) by using the self-tapping Philips screws (B10) and the
screw (B9) (see Figs. 14 + 15).
Mounting of the throttle lever (2) (Fig. 16-20)
Mount the throttle lever (2) to the handlebar (6) using screw (16a) and nut (Fig.16).
Remove the wing screw (20a) by loosening it counter-clockwise (Fig. 20).
Remove the air filter cover (8) by lifting.
Remove the wing screw (19a) by loosening it counter-clockwise (Fig.19).
Remove the air filter (19b) by lifting.
Fix all control cables as shown in figure 16.
Insert the end of the throttle lever cable into the opening at the lever (17a) (Fig.17).
Fit the throttle lever cable with the clamp (18a) as shown in figure 18.
Install air filter (19b) and cover air filter (8) in reverse order.
Mounting of the Blades cover (17) (Fig. 21-23)
•
Fix the rubber rings (B5) accordingly fig. 21
•
Attach the blades cover (17) with the appropriate screws, washers and nuts (B12) (see Fig. 22).
•
Attach the cross connector (F) with the appropriate screws, washers and nuts (B11) (see Fig.
23).
Installing the belt cover (C) (Fig. 24)
•
Fix the belt cover (C) with the wing screws (B8) as shown in fig. 24.
ATTENTION! The belt cover and blades covers must be installed!
Depth adjustment bar (19)
•
Attach the pick-up point for the holder (G) with pin (25a) and split pin (25b) as shown in fig. 25.
•
Adjust the desired side position of the holder with the adjusting screws 26A and 26B.
•
Insert the depth adjustment bar (19) into the opening (26c) at the pick-up point (G) (Fig.26) and
secure it with the fastening pin and the split pin (B6) (Fig. 27).
The depth of the bar can be adjusted in various positions.
15