Bird Gard PRO PLUS Instructions

Switch 5 Mode
ON Random mode ON
OFF Random mode OFF

PROGRAMMING EXAMPLE

Recording Switches: Results
1, 3, 5 and 6 to "ON" position Plays Bird 1, 3, 5 & 6
Mode Switches
1 = "OFF" position
2 = "ON" position (Medium), every 1 to 4 minutes
3 = "ON" position
4 = "OFF" position Operates during daylight hours only
5 = "ON" position In random, non­sequential order

VOLUME CONTROL

The unit has a volume control dial on the front
panel of the unit. Turn ing the dial toward low will
result in reduced sound output and rotating the
dial toward high will result in an increase in sound
output.
CAUTION: Take care when turning the dial since the unit may be
in an inactive state when the dial is rotated. It could then re ac ti vate
at a very high level of sound which could be painful to your ears.

POWER SWITCH

The power switch enables the unit to operate.
Slide the switch to the ON position to start the unit.
If you turn the unit OFF, be sure to leave it off for
about 30 seconds before turning it back on to allow
the electronics to properly reset.

TROUBLESHOOTING

PROBLEM SOLUTION
• Check volume settings.
Unit is on, but
• Check time of operation settings.
no sound is heard
• Check that at least one bird is
selected to play.
Unit is on, but plays the
same bird over and over, • Reset the unit by turning it off for
30 seconds and then back on.
regardless of settings
• Double check Mode
switch settings.
Unit is not operating
• Make sure photocell
is not obstructed.
properly in the
DAY or NIGHT mode • Make sure the photocell is
not affected by bright lights
in either the front or the
back of the unit.
Unit does not function
• Check battery condition.
properly when connected
• Turn power switch on unit
to a 12 volt battery (when
to the OFF position. Then
reconnect the battery, wait
using optional battery
30 seconds, then switch the
clip assembly)
unit back on.

LIMITED WARRANTY

IF YOU ARE NOT COMPLETELY SATISFIED, CONTACT THE PLACE
OF PURCHASE OR OUR CUSTOMER SERVICE DEPARTMENT WITHIN
ONE (1) YEAR OF YOUR DATE OF PURCHASE FOR PROMPT AND
COURTEOUS REPLACEMENT, REPAIR OR REFUND.
BIRD GARD LLC'S LIABILITY HEREUNDER SHALL BE LIMITED
TO REFUNDING THE PURCHASE PRICE PAID BY CUSTOMER OR
REPLACING THE PRODUCT, IN BIRD GARD'S SOLE DISCRETION,
AND UNDER NO CIRCUMSTANCES SHALL BIRD GARD BE LIABLE
FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES, OF ANY
NATURE WHATSOEVER, ARISING FROM THE CUSTOMER'S USE OR
OPERATION OF THE PRODUCT; PROVIDED, HOWEVER, THAT THIS
LIMITATION MAY BE LIMITED BY STATE LAW.
EXCEPT FOR THE EXPRESS ONE-YEAR LIMITED WARRANTY
SPECIFICALLY DESCRIBED HEREIN, BIRD GARD DISCLAIMS
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, RELATING TO
THE PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF
FITNESS; AND THE EXPRESS WARRANTIES ARE IN LIEU OF ALL
OBLIGATIONS OR LIABILITIES ON THE PART OF BIRD GARD
ARISING OUT OF OR IN CONNECTION WITH THE SALE, USE, OR
OPERATION OF THE PRODUCT.
P.O. Box 1690 • 270 East Sun Ranch Drive
Sisters, Oregon 97759 U.S.A.
1-888-332-2328 • Fax 541-549-5286
info@birdgard.com • www.birdgard.com
©2020 Bird Gard, LLC. All Rights Reserved
Bird Gard ® is a patented trademark of Bird Gard, LLC.
EPA Establishment Number 075130-OR-001
Bird Gard Pro Plus Instructions P/N 655-0058-00, Rev. D (Rev. 7-7-2020)
Digital Bird Repeller

PRIOR TO INSTALLATION

Your complete Bird
Gard ® Pro Plus kit
includes a con trol
unit, power ad apter,
ba t t ery cable with
clips and two spea k­
ers. Open the con trol
unit by lifting the two
latches on the side of
the enclosure.
Prior to operation, route the
speaker and power cables from
their respective jacks on the
control panel down through the
cutout in the lower part of the
enclosure. Be sure that the
cables are resting on the foam
pad before the cover is latched
Fig. 1
shut, as shown in Fig. 1.
IM POR TANT: Be certain that the
power switch is in the OFF po si tion
and the volume control is set to
the minimum (LOW) vol ume level
(coun ter clock wise) as shown in Fig.
2 while plugging the speakers and
power cords into the control unit.

INSTALLATION

1) Use the mounting hardware (included) to mount
the control unit box to a wall, post or other vertical
surface.
2) Plug the power adapter into an electrical outlet or
attach the battery clip as sem bly to a 12V battery.
The other end of the cable should already be
plugged into the power jack located below POWER
JACK on the front panel of the con trol unit box.
Fig. 2