PBteen Elsie Assembly Instructions Manual

Storage bed queen

Advertisement

Important safety instructions:

Please read all instruction carefully before assembling this desk.
For your safety, assembly by two or more adults is strongly recommended.
Keep these instructions for future use.
Use only vendor-supplied hardware to assembly this item. Using unauthorized hardware could jeopardize
the structural integrity of the item.
Pre- assembly:
Remove all parts and hardware from the box and place them on a carpeted or scratch-free work
surface. The shipping box provides an ideal work surface.
To avoid accidentally discarding small parts or hardware, please do not dispose of any contents until
assembly is complete.
Two people are recommended for your safety and ease of assembly.
Prior to starting the assembly, use the parts and hardware lists to identify and separate each of the
pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly
instructions.
Note: Do not fully tighten any of the bolts until all parts are in place. Failure to follow these instructions
may cause the bolts to misalign during assembly.
Please use caution if using power tools to aid in assembly. Power tools can damage the hardware or
split the wood.
Date: 2014-Oct-30
Elsie Storage Bed Queen
ASSEMBLY INSTRUCTION
www.pbteen.com
Page 1 of 8

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Elsie and is the answer not in the manual?

Questions and answers

Summary of Contents for PBteen Elsie

  • Page 1 Elsie Storage Bed Queen ASSEMBLY INSTRUCTION Important safety instructions: • Please read all instruction carefully before assembling this desk. • For your safety, assembly by two or more adults is strongly recommended. • Keep these instructions for future use. •...
  • Page 2 P – Spring Washer Q – Flat Washer Headscrew Headscrew 8x30mm 8x17mm ¼”x10x1.5mm ¼”x32xΦ13mm 1/4"x12x1.5mm 14pcs 16pcs 16pcs 28pcs 24pcs T - Leveler 3/8”x109x30mm 6pcs TOOLS REQUIRED (but not included): Phillip Head Screwdriver Date: 2014-Oct-30 www.pbteen.com Page 2 of 8...
  • Page 3 Spring Washer (P) and followed by the Short Allen Bolt (O) – 3sets; into the pre-drilled holes of the Drawer Boxes (D) bottom panel into the Siderails (C) and tightening using the Ball Tip Allen Ley (J) as shown below. Date: 2014-Oct-30 www.pbteen.com Page 3 of 8...
  • Page 4 Headboard (A) legs and tighten by using the Ball Tip Allen Key (J) as shown below. Repeat the same for the Footboard (B) as shown in the illustration below. Date: 2014-Oct-30 www.pbteen.com Page 4 of 8...
  • Page 5 Drawer Boxes (D) panels as shown below. Tighten by using the Ball Tip Allen Key (J) as shown below. 7. Adjust the levelers found underneath the Headboard (A), Footboard (B), Center Support Legs (G) and Levelers (Q) until the sit level as shown below. Date: 2014-Oct-30 www.pbteen.com Page 5 of 8...
  • Page 6 Slats Support Legs (H) in a clockwise direction for tightening as shown below. 10. Place the Slats Support Strecther (G) afix with the Slats Support Legs (H) onto the surface floor in between the Bed as shown below. Date: 2014-Oct-30 www.pbteen.com Page 6 of 8...
  • Page 7 Medium Allen Bolt (N) on the center surface of the pre-drilled holes of Slats (E). Tighen it by using the Ball Tip Allen Key (J). After fixing on the 1 Medium Allen Bolt (N), fully extend the Slats (E). Illustration as shown below. Date: 2014-Oct-30 www.pbteen.com Page 7 of 8...
  • Page 8 Avoid direct sunlight and excessive temperatures. • Dust often using a clean, soft, dry and lint-free cloth. • Waxing is not recommended on lacquered finish. • Hardware should be checked periodically for tightness. Date: 2014-Oct-30 www.pbteen.com Page 8 of 8...

Table of Contents