Table of Contents
Advertisement
4
. Attach
3/4" U.L.-
listed strain relief (U.L.
marking on strain
relief) to the hole
below terminal box
opening
(see Figure
12). Tighten strain
relief firmly to cabinet
so it is in a horizontal
position. Place direct
(outside dryer)
wire cable through
the strain relief.
Figure 12
,i$ 5
. Remove
the center
terminal
..!, !! ,: block screw, Remove
the neutral
,Y - i green
with yellow stripe ground
wire
::. :. :
i - '! from external
ground
conductor
.! :
j ;, ; screw.
Connect
neutral
green with
. . !: yellow stripe ground
wire and the
;.;.j..; neutral
wire (white
or center)
of
$j ! direct wire cable
under the center
$I:':.: screw of terminal
block. Place the
$;i:i:i. hook-shaped
end of the wire over
:.$$< the terminal
block screw with open
':$:.: side of the hook facing
to the right.
Ii:; i Squeeze
hook end of wire together
! I ._ ; to form a loop.
Z$.ii j Connect
the other two insulated
;:;si..i wires under outer terminal
block
I: i. screws. Attach
wires using the same
$ ;.I method
as the neutral
wire.
..j.$ ; Connect
the direct wire cable
(bare
.; .;
f; :; ground
wire to the external
ground
: 1 conductor
screw (see Figure 13).
.: i. Tighten
all terminal
block screws
:,; j : firmly.
neutral green with yellow
stripes (attached at
~; z jexternal
factory)
Figure 13
strain relief screws.
. Insert tab of terminal
block
:.i :I. cover into slot of the dryer rear
i' '$. panel
(see Figure 1 1). Secure cover
/z-i. with hold-down
screw.
. . . . ::
B.
Where local codes
permit
connecting
frame-ground
conductor
to the neutral
wire:
This dryer is manufactured
with the
frame-ground
conductor
connected
to the NEUTRAL (center)
of the wiring
harness at the terminal
block.
If local
codes do Not permit
this type of
connection,
use "Four-wire
connection"
instructions.
Electrical
Shock
Hazard
Turn power
supply
off before
connecting
cord.
rounded
outlet.
1
. Turn power supply
off.
2
. Remove hold-down
screw and
terminal block cover.
external ground
hold-
3
. Attach
3/4" U.L.-listed strain
relief (U.L. marking
on strain relief)
to the hole below
terminal
box
opening
(see Figure 15). Tighten
strain relief firmly to cabinet
so it is
in a horizontal
position. Place
power supply cord through
strain
relief.
strhin relief
(outside dryer)
Figure 15
#i: 4
. Loosen or remove
terminal
: : :
block screws. Connect
the neutral
: :
: : wire (white
or center)
of power
: 1 :. j supply cord under the center
screw
: ; ,; of the terminal
block.
' ,: : Connect
the other two wires to
: : : :
outer terminal
block screws (see
: j : Figure 16).
: :
: :
: : :
Tighten
all terminal
block screws
j :
firmly,
: : : :
Center wire MUST be connected
to
: : c
center
screw.
: : :. .:
: : : :
: : : :
external ground
: :
: c
: :
strain relief
screws
: :
! :
Figure 16
i.
5
. Tighten
strain relief screws.
6
. Insert tab of terminal
block
: cover into slot of the dryer rear
panel
(see Figure 14). Secure cover
with hold-down
screw.
: : : :
: :
::: : :
:
Page 8
Advertisement
Table of Contents
