Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vicon V3000APT-1
Summary of Contents for Vicon V3000APT-1
- Page 1 X323 MODEL V3000APT-1 INDOOR PAN-AND-TILT DRIVE VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788-9633 TELEPHONE: 516-952-CCTV (2288) FACSIMILE: 516-951-CCTV (2288) TOLL FREE: 1-800-645-9116 UK: 44/(0) 1489-566300 INFOFAX: 1-800-287-1207...
- Page 4 Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture. Copyright © 1998 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. Vicon Part No. 8006-8323-03-00 Section 1 Rev 498...
- Page 5 This page intentionally left blank. Contents • • iii X323 Rev 498 V3000APT-1 Pan-and-Tilt Drive...
- Page 7 We stand behind the quality and dependability of every product with an industry leading Beneficial Use warranty. If you are not satisfied with a Vicon product or service, I would like to know. Your complete satisfaction is the mission of every Vicon employee.
- Page 9 This page intentionally left blank.
-
Page 11: Table Of Contents
Mounting the Unit ..........................2 Inverted Mounting..........................2 Wiring the Unit............................. 3 Adjusting the Limit Stops........................4 Mounting the Camera .......................... 5 Operation and Maintenance ......................6 Shipping Instructions........................7 Contents • • i X323 Rev 498 V3000APT-1 Pan-and-Tilt Drive... -
Page 12: List Of Figures
List of Figures Figure 1 V3000APT-1 Cable Assembly Diagram ....................2 Figure 2 Limit Stop Adjustment..........................5 Figure 3 V3000APT-1 Camera Mounting-Plate Latch..................... 5 ii • • List of Figures X323 Rev 498 V3000APT-1 Pan-and-Tilt Drive... -
Page 13: Important Safeguards
Use only with a mounting accessory recommended by Vicon, or sold with the video product. Any mounting of the video product should follow Vicon’s instructions, and a mounting accessory recommended by Vicon should be used. - Page 14 Vicon or that have the 15. Power Lines - An outside cable system should not same characteristics as the original part. Unauthorized...
-
Page 15: Introduction
The V3000APT-1 may be energized using an appropriate 24 VAC control unit or a combination of a 24 VAC control unit with an appropriate relay box. The table in the Installation chapter lists maximum operating distances. -
Page 16: Installation
V1600WM Wall Mount. The camera must be correctly mounted and balanced on the unit. The V3000APT-1 may also be mounted directly to a rigid, flat surface capable of supporting the combined weight of the unit and camera when the V3200SB Square Base option is used. -
Page 17: Wiring The Unit
6. Fold the strain relief along its molded hinge, making sure that the small lugs on the connector fit into the recesses of the strain relief. 7. Make sure the flange of the grommet is inside the strain relief, and screw the strain relief closed with the screw provided. Installation • • 3 X323 Rev 498 V3000APT-1 Pan-and-Tilt Drive... -
Page 18: Adjusting The Limit Stops
9. Drive the tilt to the DOWN limit desired and then rotate the right knob counterclockwise until a click is heard. Tighten the screw. 10. Drive the tilt to both stop positions to check position accuracy. Repeat steps 8 and 9 if necessary. Figure 2 4 • • Installation X323 Rev 498 V3000APT-1 Pan-and-Tilt Drive... -
Page 19: Mounting The Camera
5. Place the camera attached to its mounting plate on the unit, facing it in the proper direction, and slide the two (2) latches to the right, securing the camera to the unit. Figure 3 V3000APT-1 Camera Mounting-Plate Latch Installation • • 5 X323 Rev 498 V3000APT-1 Pan-and-Tilt Drive... -
Page 20: Operation And Maintenance
Operation and Maintenance The V3000APT-1 is operated by an appropriate remote control unit. Refer to the instruction manual supplied with the control for details of operation with this unit. The V3000APT-1 pan-and-tilt is factory-lubricated and requires no lubrication or maintenance for the life of the unit. -
Page 21: Shipping Instructions
Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A.
Need help?
Do you have a question about the V3000APT-1 and is the answer not in the manual?
Questions and answers