Table of Contents
Advertisement
10
WARNING
Before inspecting, cleaning or servicing
the machine, shut off engine, let all
moving parts come to a complete stop,
disconnect the spark plug wire and move
the wire away from the spark plug.
Failure to follow these instructions can
result in personal injury or property
damage.
EQUIPMENT MAINTENANCE
Transmission Maintenance
The transmission was lubricated at the
factory and should not require any further
lubrication.
However, you should check the lubricant
level after the first five (5) hours of opera-
tion and every twenty-five (25) operating
hours thereafter. If needed, use a high-
quality, automotive-grade petroleum-
based grease.
WARNING
Before tipping engine or equipment to
service transmission, drain fuel from
tank by running engine until fuel tank is
empty. Allow engine to cool.
To check the transmission:
1. Stop the engine, let it cool and discon-
nect the spark plug wire.
2. Place the machine down on its left side
so the right end of the tine shaft faces up.
3. Remove the right-side tines (see Tine
Removal and Installation in this Section).
4. Clean the transmission housing.
5. Remove the three threaded plugs (A, B
and C, Figure 11) from the transmission.
D
A
B
Figure 11: Transmission lubricant check and
fill locations.
Section
Maintenance
5
REQUIRED MAINTENANCE
Perform at every indicated month or
operating hour interval, whichever
comes first.* See Engine Owner's Manual
for engine related maintenance.
Check Tightness of Bolts and Nuts
Check Transmission Lubricant Level
Clean Machine
Clean Tine Shaft
Engine Oil Level
Air Cleaner
Spark Plug
Cooling Fins
Spark Arrester
Fuel Tank
Fuel Filter
Clutch Shoes
Idle Speed
Valve Clearance
Fuel Tubes
*
For commercial use, log hours of operation to determine proper maintenance intervals.
(1) Check after first 5 hours of use.
(2) Service more frequently when used in dusty areas.
(3) Item should be serviced by your servicing dealer, unless you have the proper tools and
are mechanically proficient.
Lubricant should be visible in the top two
holes (B and C). If so, replace all three
plugs. If lubricant is needed, proceed as
follows.
To lubricate the transmission:
1. Place the nozzle (D, Figure 11) of a
standard grease gun firmly against the rim
of the middle hole (B) and add grease until
it begins to seep from the bottom hole (A).
Reinstall the plug in the bottom hole (A).
Next apply grease to the top fill hole (C)
until it begins to seep from the middle
C
hole (B). Reinstall the plugs in the middle
(B) and top (C) holes.
2. Before reinstalling the tines, use a fine
grade sandpaper to clean any rust off the
tine shaft. Apply a few drops of oil to the
shaft to make future tine removal easier.
REQUIRED MAINTENANCE SCHEDULE
Before
Each
month
Use
or 10 Hrs. or 25 Hrs. or 50 Hrs.
x
x
Check
x
Change
Check
x
Change
Check/Clean
Replace
Check
Clean
Clean
Check
Check
Check-Adjust
Check-Adjust
Check
Other Lubrication Points
• Handlebar Adjustment Knobs: Spray
occasionally with a silicone lubricant.
• Throttle/Tines Control Lever Cable:
Squeeze the lever closed and spray a
lubricant into the cable area.
• Tine Shaft: After each use, remove the
tines, clean the tine shaft with sandpaper
and apply a light coat of oil to the shaft.
Hardware/Electrical Connections
Before each use, check that all hardware is
tight and that the On/Off Switch wire con-
nections are secure. Also check that the
switch wiring is in good condition.
First
Every 3
Every 6
Yearly
months
months
x (1)
x
x
x (2)
x
x
x (3)
x (3)
Every 2 years (Replace if necessary) (3)
Every
2 years
x
x
x
x
x
x
x (3)
Advertisement
Table of Contents
