Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bolens 12207
Summary of Contents for Bolens 12207
-
Page 1: Parts List
SAFETY FIRST! Before operating this equipment, read this Owner's Manual and the separate manual supplied by the engine manufacturer. Model 12207 OWNER’S MANUAL Tiller/Edger • Safety • Assembly • Operation • Maintenance/Service • Parts List GARDEN WAY INCORPORATED... -
Page 2: Safety Rules
CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND PLACE WIRE WHERE IT CANNOT CONTACT SPARK PLUG TO PREVENT ACCIDENTAL STARTING WHEN SETTING UP, TRANSPORTING, ADJUSTING OR MAKING REPAIRS. TRAINING • Read this Owner’s Manual and the separate Engine Owner’s Manual very carefully before operating this equipment. Be completely familiar with the controls and the proper use of the equipment. - Page 3 • Start the engine carefully according to instructions and with feet well away from the tines. MAINTENANCE/STORAGE • Keep the tiller, attachments and accessories in safe working condition. • Check all nuts, bolts, and screws at frequent intervals for proper tightness to be sure equipment is in safe working condition.
-
Page 4: Table Of Contents
B71.8 – 1996, which is sponsored by the Outdoor Power Equipment Institute, Inc., and is published by the American National Standards Institute. CONGRATULATIONS on your purchase of a Tiller/Edger with Edger Attachment. It has been designed, engineered and manufactured to give you the best possible dependability and performance. -
Page 5: Accessories And Attachments
FORWARD noted otherwise). ACCESSORIES/ATTACHMENTS The following accessories and attachments are available where the Tiller/Edger was purchased. See your authorized dealer or contact the Factory for details. Power Lawn Rake Attachment – Model 12575 The Power Lawn Rake will help keep your lawn healthy and vigorous. -
Page 6: Assembly
(1) Border/Edger Wheel Parts packed separately in carton (not shown full size) Read these instructions in their entirety before you attempt to assemble or operate your new equipment. The Border Edger Attachment does not need to be installed until you are ready to do edging projects (refer to instructions in this Section). - Page 7 height setting holes. If this height is correct for you, simply tighten the two handlebar knobs. If a higher setting is desired, reposition the handlebar knobs, mounting screws and washers in the other set of holes. • Check the locations of the three plastic ties (C, Figure 1). The ties must be positioned as shown.
-
Page 8: Borders
Then place the Border/Edger wheel (C) on the same shaft – the wheel hub should face toward the tiller. Insert the ring lock pin through the rounded side of the Metric Measure tine shaft and snap the ring down over the shaft (see “DETAIL”, Figure 4). -
Page 9: Operation
KNOW YOUR EQUIPMENT READ THIS OWNER’S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR EQUIPMENT. Know the location and function of all features and controls on the equipment. Save this manual for future reference. WARNING Contact with rotating tines or other moving parts will cause serious personal injury! Before inspecting or servicing any part of the machine, shut off engine, let all moving parts come to a complete stop, dis-... -
Page 10: Stopping And Starting The Engine
• Do not allow open flames, sparks, matches, or smoking in fueling area. • Fill fuel tank outdoors in a well-ventilated area. • Wipe up any spills and move tiller away from fumes before starting engine. • Use only an approved fuel container and lock it safely away from children. -
Page 11: Cultivating
Priming When Cold Starting: Use this priming method to start the engine after it has been sitting or has been in brief storage, and has fuel in the tank. Use the Standard-Volume Priming Position (Figure 6) and push in top of primer bulb two (2) times for above 55 times if below 55 When Warm Starting: Do not use the primer to restart the engine after it has been... -
Page 12: Borders
Tips and Techniques • Adjust engine speed to suit the tilling conditions. Remember that the rotating tines help to pull the machine forward. Use slower speeds and a shallow depth setting when learning to use the unit and whenever you are tilling on hard, rough or uneven ground. -
Page 13: Maintenance/Service
WARNING Before inspecting, cleaning or servicing the machine, shut off engine, let all moving parts come to a complete stop, disconnect the spark plug wire and move the wire away from the spark plug. Failure to follow these instructions can result in personal injury or property damage. -
Page 14: Carburetor
Engine Air Filter It is very important that air filter service be performed accord- ing to the maintenance schedule. Refer to the separate Engine Owner’s Manual for inspection and cleaning instructions. IMPORTANT: Never run engine without air filter assembly prop- erly installed. -
Page 15: Storage
• Slide one of the long bushings (provided with unit) onto the shaft. See Figure 17. Insert the ring lock pin through the rounded side of the tine shaft and snap the ring down over the shaft (see DETAIL, Figure 4, in the Assembly Section). •... -
Page 16: Troubleshooting
PROBLEM Engine does not start. 1. Spark plug wire disconnected. 2. Out of gas/two-cycle oil fuel mixture. 3. Stale fuel mixture. 4. Priming procedure not correct. 5. Dirty air filter(s). 6. Worn, corroded or broken spark plug. 7. Engine On-Off Switch in OFF position. Engine runs poorly or 1. - Page 17 Plug, 1/8 ......3 1111600 Hex Screw, 1/4-20 x 7/8 (five locations, identified as “A” on transmission case) . . . 5 A/R – As Required REPAIR PARTS – Model 12207 16, 17 14, 15 TRANSMISSION ASSEMBLY Ref # Part #...
- Page 18 REPAIR PARTS – Model 12207 SEE PREVIOUS PAGE...
- Page 19 Lock Washer, 1/4-20 ....4 Order parts from your local authorized engine dealer. Refer to engine nameplate for model/type number. REPAIR PARTS – Model 12207 Ref # Part # EDGER ATTACHMENT...
-
Page 20: Customer Service Information
CUSTOMER SERVICE INFORMATION Owner Registration Card Please fill out and mail the enclosed owner registration card. The purpose of this card is to register each unit at the factory in order to keep the owner informed with informational bulletins and safety literature. Model/Serial Numbers A Model Number/Serial Number decal is located on the handlebar.